---
title: "Light switch stopped working | 4.7 Star · NAPIT approved · From £60"
description: "Light switch not working in Peterborough: Lighting Electrical measures the lighting circuit and names the failed switch, lamp or joint. · Call 07414 545781"
canonical: "https://lightingelectrical.co.uk/problems/light-switch-not-working"
---

# Light switch stopped working

> Light switch not working in Peterborough: Lighting Electrical measures the lighting circuit and names the failed switch, lamp or joint. · Call 07414 545781

A light switch that does nothing means the switch, the lamp or the lighting circuit has failed. Lighting Electrical in Peterborough measures that lighting circuit and tells you the failed part.

## Why has a light switch stopped working?

A light switch stops working because the switch, the lamp or the lighting circuit has failed. Other lights can stay on, because each lighting circuit leaves the fuse board on its own protective switch.
- **Worn contacts inside the switch:** The rocker still clicks, but the metal contacts inside no longer meet. That one light stays off. Other lights on the same circuit stay on.
- **The lighting breaker has opened:** A breaker is the switch in the fuse board that guards one circuit. It opens on a short or an overload. Every light on that circuit goes out together.
- **A lamp or lampholder has failed:** A spent lamp looks like a dead switch. The lampholder is the part that grips the lamp. A burnt lampholder stops that fitting even when the switch still works.
- **A loose joint on the lighting loop:** Many lights share one cable that loops from fitting to fitting. A loose terminal in a ceiling rose, the joint above the lamp, or in a switch opens the lights past that point. The breaker can stay up.
- **A dimmer that fights the lamp:** A dimmer sets brightness by cutting the supply in rapid slices. An LED lamp, the low energy type, stays dark or flickers if the dimmer cannot drive it. A plain switch on the same cable would light a matching lamp.
- **A two way strap has come loose:** Two way switching uses two switches for one light. The strap is the extra wire between those switches. A loose strap kills the light from both rockers.

## What can I check with the switch still shut?

You can try a known lamp, see which other lights still work, and read the fuse board through the closed cover. Leave every screw in place.
- **A lamp from a working fitting:** Move a lamp from a light that already works into the dead fitting. If it stays dark, the switch or the circuit is at fault. If it lights, the old lamp had failed.
- **Lights in the same rooms:** Turn on the other lights in that room and the next room. One dead light points to its switch or fitting. A dark floor points to the lighting breaker.
- **The breaker behind the closed cover:** Find the breaker named for lights and read it through the closed cover. One reset is reasonable if the board feels cool, makes no sound and has no burning smell. If it drops again, leave it off.
- **Heat, a buzz or a soft rocker:** A warm plate, a buzz or a rocker that feels soft means the switch is failing. Leave that light switched off at the rocker if it still moves. Do not take the plate off.

## When should I book for a dead light switch?

Book Now when a known lamp stays dark, the lighting breaker drops again, or the switch is warm, noisy or smells of burning.
- **A good lamp and the light stays off:** The replacement lamp already works in another fitting and the lighting breaker is up. The fault sits in the switch, the fitting or the cable between them. Book Now.
- **The lighting breaker drops again:** The breaker opens after one reset with no extra lamps added. Another reset heats the cable. Leave that breaker off and Book Now.
- **The switch is warm or smells burnt:** Heat, a buzz or a burning smell means the contacts are arcing. Arcing is a spark jumping a loose joint. Use the breaker on the closed fuse board to switch that circuit off.
- **Several lights went out together:** More than one light dead on the same floor means the lighting circuit has opened. Fitting one new switch on a single wall will not bring the other lights back.

## What happens on a visit for a dead light switch?

We switch off the lighting circuit and name the failed switch, lamp, joint or breaker before a part comes off the wall.
- **Which light died and when:** We ask which light stopped, whether a dimmer is fitted, and when it last worked. We look at the fuse board with you and the cover remains closed. We note the lighting breaker.
- **Measurements with the circuit off:** We turn the lighting circuit off at its breaker. Continuity shows whether the copper still connects. Insulation shows whether current leaks between the wires. The two readings separate the switch, the cable and the fitting.
- **Only the part the tests name:** We open the switch or the fitting the readings point to. A sound switch stays screwed on. Where a switch has failed we fit MK Electric, Varilight or BG Electrical.
- **The repair and the certificate:** The repair of that switch, joint or breaker starts once you accept it. We test the lighting circuit again afterwards. A circuit change is written on a minor works certificate carrying our NAPIT registration. Earthing, the fault path back to the board, and bonding, the link from metal pipes to that earth, are checked with spare supply capacity before any further price.

## What does a dead light switch visit cost?

The time spent on Electrical Fault Finding & Repair sets the price. That time covers measurements on the lighting circuit, the diagnosis we speak to you, and the start of the repair once you accept it. A single switch takes less time than a fault along a loop of fittings. A new switch, a minor works certificate or a fuse board replacement changes the price.
- Fault finding & repair: from £75 an hour
- A replacement switch or dimmer is added only after the measurements show that part has failed.
- MK Electric, Varilight and BG Electrical are the switch brands we fit when the old one has failed.
- A failed lighting breaker moves the job onto fuse board replacement, priced on its own.

## Questions about a light switch not working

### Will you change the switch before you find the fault?

No. We measure the lighting circuit and name the failed switch, lamp, joint or breaker first. The repair starts only after you accept it. A switch that still tests sound stays on the wall.

### Why is only one light dead?

Each switch opens only its own lamp, even when several lights share one cable from the fuse board. Worn contacts kill that lamp alone. The rest stay lit until the shared cable or the breaker fails.

### What paperwork follows a switch repair?

A switch change that alters the circuit is recorded on a minor works certificate. The certificate lists the test results and our NAPIT registration. An Electrical Installation Condition Report, an EICR, looks over the whole installation and is arranged as another job.

### Will a new fuse board bring the light back?

Only if the measurements show the lighting breaker or the board has failed. A worn switch or a loose ceiling joint still leaves that lamp dark on a new board. Any board change has its own written price.

### Is a dimmer fault the same as a switch fault?

Often the dimmer is the failed part, especially with an LED lamp it cannot drive. We test the dimmer and the lamp before we fit a replacement. Light switch or dimmer replacement goes ahead once you accept it.

## Related problems
- [Automatic gate not opening](https://lightingelectrical.co.uk/problems/electric-gate-not-working): A gate that will not move has lost its supply, its safety beam or its motor control, so the outdoor circuit needs a test.
- [Buzzing sound in the wall](https://lightingelectrical.co.uk/problems/buzzing-in-walls): A buzz inside a wall is a loose joint, a dimmer or a damaged cable on that circuit.
- [Circuit breaker keeps tripping](https://lightingelectrical.co.uk/problems/circuit-breaker-keeps-tripping): The breaker keeps tripping because a fault is still on the circuit, in an appliance, a cable, a joint or the protective device.
- [Consumer unit tripping with nothing plugged in](https://lightingelectrical.co.uk/problems/consumer-unit-tripping-nothing-plugged-in): The consumer unit trips with nothing plugged in because fixed wiring or the safety switch is sending current to earth.
- [Downstairs circuit keeps tripping](https://lightingelectrical.co.uk/problems/downstairs-circuit-keeps-tripping): The downstairs breaker or RCD opens because a socket, light, cable or appliance on that floor is leaking or overloaded.
- [Driveway lights not working](https://lightingelectrical.co.uk/problems/driveway-light-not-working): Driveway lights go dark when the outdoor circuit, a sensor or a lantern fails, while rooms on another breaker stay lit.

## Sources
- [BS 7671: IET Wiring Regulations (18th Edition)](https://electrical.theiet.org/bs-7671/)
- [Electrical Safety First: Safety Guidance](https://www.electricalsafetyfirst.org.uk/guidance/)
- [NICEIC: Householder Guidance](https://niceic.com/householders/)

Updated 2026-11-16.

[Electrical fault finding](https://lightingelectrical.co.uk/services/electrical-fault-finding)

## Book or ask a question
- [Book Now](https://lightingelectrical.co.uk/#chat)
