---
title: "Why are my lights too dim? | 4.7 Star · NAPIT approved · From £60"
description: "Dim lights in Peterborough come from a lamp, a dimmer or the lighting circuit. Lighting Electrical tests that circuit and names the dull part."
canonical: "https://lightingelectrical.co.uk/problems/lights-too-dim"
---

# Why are my lights too dim?

> Dim lights in Peterborough come from a lamp, a dimmer or the lighting circuit. Lighting Electrical tests that circuit and names the dull part.

Dim lights mean the lamp, the dimmer or the lighting circuit is not delivering full brightness. Lighting Electrical tests that circuit and names the part holding the light back.

## Why are the lights too dim?

Lights are too dim when the lamp, the dimmer or the lighting circuit cannot deliver full power. The lighting circuit is the cable and breaker that feed the lamps.
- **A lamp that no longer gives full light:** A lamp with a low output looks dull on a sound circuit. Output is the amount of light the lamp produces. A blackened filament lamp or a failed LED lamp gives that dull light even when the wiring is sound.
- **A dimmer that does not suit the lamps:** A dimmer reduces the power sent to the lamps. Older dimmers were built for filament lamps, so LED lamps on them stay dull and can buzz. We fit a Varilight or MK Electric dimmer only when the tests show that dimmer has failed.
- **A loose joint on the lighting circuit:** A loose terminal in a ceiling rose or a switch resists the flow of current. The wasted power becomes heat, so the lamps receive less electrical pressure and look dim. The plastic around the switch can warm up.
- **Voltage lost along the lighting cable:** Voltage drop is electrical pressure lost along a cable. A lighting circuit that has been extended, or wired in cable that is too thin, leaves the furthest lamps dull. Lamps nearer the fuse board stay brighter on the same circuit.
- **A dip when a heavy appliance runs:** A shower, oven or kettle pulls a large current. Lamps across the house can fade at that moment if a supply connection or the main neutral is loose. The neutral is the conductor that carries current back to the supply. New lamps do not cure that dip.

## What can I check while the covers stay on?

You can compare rooms, fit a known lamp and move the dimmer. The switch stays shut and the fuse board cover stays on.
- **One room against the rest of the house:** Turn the lights on in two rooms. Dull lamps in a single room point to those fittings or their dimmer. Dull lamps in every room point to the lighting circuit or the incoming supply.
- **A lamp you already trust:** Fit one lamp that looks bright in another room and set the dimmer to its highest mark. A still dull fitting means the old lamp was not the cause. A bright result means the old lamp had failed.
- **The dimmer at its highest mark:** Push the dimmer all the way up. A slider left low keeps a healthy circuit looking dull. If it will not reach a bright light with LED lamps, leave the screws in the switch.
- **Lamps while a kettle or shower runs:** Watch the lamps as the kettle boils or the shower starts. A fade only at that moment points away from a single failed lamp. Steady dullness with those appliances off points to the dimmer or the lighting cable.

## When should I book for dim lights?

Book Now when a trusted lamp stays dull, the dimmer buzzes or warms, or rooms fade each time a heavy appliance runs.
- **A new lamp is still dull:** You fitted a lamp that is bright elsewhere and the room stays dim at the top of the dimmer. The dimmer or the lighting cable needs a test. Another lamp in the same fitting will not find a loose joint.
- **The dimmer is warm, buzzing or smelly:** Heat, a buzz or a burning smell means the dimmer or a terminal is struggling. Leave the screws alone. Use the handle on the fuse board to switch the lighting breaker off if the smell is strong.
- **Lights fade in several rooms at once:** Lamps that fade when the shower, oven or kettle runs need a measurement at the supply. Book Now so that connection can be tested while the pattern is clear. Keep using the circuits that stay bright.
- **The far end of the lighting circuit is dull:** Lamps close to the fuse board look normal and lamps in the furthest rooms look dull. That pattern fits voltage drop on a long or extended lighting cable. The circuit needs a test before more fittings are added.

## What happens on a visit for dim lights?

We measure the dull lighting circuit and name the lamp, dimmer, joint or cable before any part is changed. The repair waits until you accept it.
- **Which rooms look dull:** We ask which rooms are dull, whether a dimmer is in use, and whether the lamps fade when a shower or kettle runs. We look at the lighting breaker with you without taking the fuse board cover off. We note any lamp you have already changed.
- **Tests that show where the voltage is lost:** We switch the lighting circuit off and test whether the cable is continuous and whether current leaks between the conductors. We then switch it on and measure voltage at the fuse board and at the dull fitting. Those readings separate a lamp, a dimmer, a joint and the cable.
- **The cause named before a part is fitted:** We tell you the failed part in plain words. A dimmer or ceiling rose that tests sound stays in place. Before any further price we check the earth path, which carries a fault away from you. We also check the bonds from metal pipes to the fuse board, and whether the supply can feed the load.
- **The repair on the hour you accept:** The hourly repair puts right the part the tests named. We fit a dimmer, remake a joint or replace a short run of lighting cable only after you accept the work. We test the circuit again once that repair is done. Where the circuit was altered, the minor works certificate records the job through our NAPIT registration.

## What does dim light fault finding cost?

Electrical Fault Finding & Repair is billed by the hour. That hour covers tests on the dull lighting circuit, a spoken diagnosis, and the opening stage of the repair after you accept the work. Replacing one failed dimmer takes less time than tracing voltage drop through several ceiling points. A part, a minor works certificate, or a separate fuse board job changes the price.
- Fault finding & repair: from £75 an hour
- A Varilight, MK Electric or BG Electrical dimmer is fitted only after the tests show it has failed.
- Voltage drop across several fittings takes more time than one failed lamp holder.
- A failed fuse board is quoted as fuse board replacement, apart from the lighting repair.

## Questions about lights that are too dim

### Will a brighter lamp cure dim lights?

A brighter lamp cures the room only when the old lamp was the dull part. If a trusted lamp stays dim at the top of the dimmer, the dimmer or the lighting circuit is limiting the voltage. We test and name which one it is.

### Can a dimmer make LED lights look dim?

Yes. A dimmer made for filament lamps often holds LED lamps below full brightness and can make them buzz. We test that dimmer before we change it. A dimmer that passes stays on the wall.

### Do you swap fittings before finding the cause?

No. We name the failed lamp, dimmer, joint or cable first. The repair of that part starts only after you accept the hourly work. Anything that tests sound is left in place.

### Do I get a certificate after the repair?

Where we alter the lighting circuit, you receive a minor works certificate for that job. The certificate lists the readings for the alteration and shows our NAPIT registration. An EICR is a separate inspection of the whole installation.

### Why do the lights dip when the shower starts?

A dip at the moment the shower or oven starts can come from the supply or a loose neutral. It is not always a failed lamp. We measure at the fuse board while that appliance runs and name the part that is dropping the voltage.

## Related problems
- [Automatic gate not opening](https://lightingelectrical.co.uk/problems/electric-gate-not-working): A gate that will not move has lost its supply, its safety beam or its motor control, so the outdoor circuit needs a test.
- [Buzzing sound in the wall](https://lightingelectrical.co.uk/problems/buzzing-in-walls): A buzz inside a wall is a loose joint, a dimmer or a damaged cable on that circuit.
- [Circuit breaker keeps tripping](https://lightingelectrical.co.uk/problems/circuit-breaker-keeps-tripping): The breaker keeps tripping because a fault is still on the circuit, in an appliance, a cable, a joint or the protective device.
- [Consumer unit tripping with nothing plugged in](https://lightingelectrical.co.uk/problems/consumer-unit-tripping-nothing-plugged-in): The consumer unit trips with nothing plugged in because fixed wiring or the safety switch is sending current to earth.
- [Downstairs circuit keeps tripping](https://lightingelectrical.co.uk/problems/downstairs-circuit-keeps-tripping): The downstairs breaker or RCD opens because a socket, light, cable or appliance on that floor is leaking or overloaded.
- [Driveway lights not working](https://lightingelectrical.co.uk/problems/driveway-light-not-working): Driveway lights go dark when the outdoor circuit, a sensor or a lantern fails, while rooms on another breaker stay lit.

## Sources
- [Electrical Safety First: Safety Guidance](https://www.electricalsafetyfirst.org.uk/guidance/)
- [BS 7671: IET Wiring Regulations (18th Edition)](https://electrical.theiet.org/bs-7671/)
- [NICEIC: Householder Guidance](https://niceic.com/householders/)

Updated 2026-11-16.

[Electrical fault finding](https://lightingelectrical.co.uk/services/electrical-fault-finding)

## Book or ask a question
- [Book Now](https://lightingelectrical.co.uk/#chat)
