---
title: "Electrical hum in the house | 4.7 Star · NAPIT approved · From £60"
description: "Electrical hum in a Peterborough house is traced by Lighting Electrical at the fuse board, naming the transformer, dimmer or loose joint before repair."
canonical: "https://lightingelectrical.co.uk/problems/mains-hum"
---

# Electrical hum in the house

> Electrical hum in a Peterborough house is traced by Lighting Electrical at the fuse board, naming the transformer, dimmer or loose joint before repair.

A steady electrical hum in the house often comes from a transformer or a loose joint. Lighting Electrical in Peterborough tests the fuse board and names the part that hums before any repair.

## Why is there a mains hum in the house?

The house hums because a transformer or a loose joint is vibrating on the mains. A transformer changes the voltage, and its iron core can buzz while it is energised.
- **A transformer buzzing on the mains:** A transformer changes mains voltage for a doorbell, a shower pump or a fitting inside the fuse board. Its iron core vibrates and makes a steady low hum. The hum continues while that part stays energised, even when portable appliances are unplugged.
- **A dimmer or a lamp driver:** A dimmer cuts the mains wave to lower a lamp, and that cutting can buzz in the switch. A driver is the small supply inside an LED lamp, and it can hum on the same circuit. Varilight dimmers are a common place we meet this buzz.
- **A loose terminal that sparks:** A loose terminal lets the copper spark across a small gap. That spark is called arcing, and it makes a sharp buzz. Heat and brown marks build if the joint stays loose under load.
- **A charger or an inverter under load:** An EV charger from Ohme, myenergi, Hypervolt or Andersen can hum while it charges. A solar inverter can hum while it feeds the house. The hum rises with the load and falls when charging or generation stops.
- **The network transformer in the street:** A network transformer on the street supply can send a low hum into the house. Switching indoor breakers does not stop it, because the hum arrives on the incoming mains. We still test the installation so a loose joint is not missed.

## What can you check with the covers on?

You can listen, unplug portable items and use the breaker handles with the fuse board cover left on. You leave every screw in place and you do not open an appliance.
- **Which rooms hum:** Stand in each room and note where the hum is loudest. A hum beside the fuse board points to a part in the board. A hum beside one lamp points to that dimmer or that lamp.
- **Plugs and dimmers:** Unplug phone chargers, lamps and other portable items. Turn each dimmer to full brightness, where many dimmers go quiet. If the hum remains, the vibrating part is still in the fixed wiring or the fuse board.
- **Breaker handles with the cover on:** A breaker is the switch on the fuse board that protects one circuit. Cover left closed, switch one breaker off and listen. The hum stopping names that circuit. The hum continuing means you switch that breaker back on and try the next.
- **Heat, smell or a harsher buzz:** Touch only the outside of a socket or the closed fuse board. Warm plastic, a burning smell or a harsh buzz means leave that circuit off. Use the breaker handle on the front. Leave the screws alone.

## When should you book for a mains hum?

Book Now when the hum comes with heat or a burning smell, or when it stays after you unplug portable items and set dimmers to full. A new harsh buzz at the fuse board needs a test.
- **Heat or a burning smell with the hum:** Warm plastic, brown marks or a burning smell means a joint is arcing. Switch that circuit off at the breaker handle. Book Now with the circuit left off.
- **The hum stays after simple checks:** The hum remains after portable plugs are out and dimmers are at full brightness. The vibrating part then sits in the fixed wiring, a fitted transformer or the fuse board. That part needs a test with the circuit isolated.
- **A loud hum from the fuse board:** A fuse board that newly hums, or hums louder than before, can hold a loose transformer or a tired breaker. Leave the cover on. Book Now so we can test the board and the earth path.

## What happens on a mains hum visit?

We listen for the hum with you, then test from the fuse board and name the vibrating part. Any repair waits until you accept it.
- **Where you hear the hum:** We ask which rooms hum and when the noise started. We note whether it follows an EV charge, solar generation, a dimmer or the fuse board. We look at the closed board with you and record which breakers are on.
- **Tests that name the vibrating part:** We switch off the humming circuit at its breaker. A dead test checks the cable while it is off. Continuity shows whether the copper still joins end to end. Insulation shows whether current leaks between the conductors. The readings separate a transformer, a dimmer, a terminal, a charger and an inverter.
- **Earth path and supply before a further price:** We test the earth path, the safe way fault current leaves the circuit. We test bonding, the link from metal pipes back to that earth. We also test whether the supply can carry another load before we price any further work.
- **Repair of the part that failed:** We change the failed transformer, dimmer, terminal or device after you accept that repair. We test the circuit again. Where the circuit was altered we issue a minor works certificate through our NAPIT registration. If the network transformer is humming and the installation tests sound, we leave the circuits on.

## What does a mains hum visit cost?

Electrical Fault Finding & Repair is charged by the hour. The price covers listening for the hum, the circuit tests, the spoken diagnosis, and the first part of the repair after you say yes. A longer search, a replacement part, or a minor works certificate changes the price. A fuse board change is priced as its own job when the tests show the board has failed. Emergency electrician attendance is priced separately.
- Fault finding & repair: from £75 an hour
- Tracing a hum behind several dimmers takes longer than confirming one charger that only hums while it charges.
- A Varilight dimmer, a breaker or a transformer from Hager, Wylex, Contactum, BG Electrical or MK Electric is fitted only when the tests show it has failed.
- Fuse board replacement and emergency electrician attendance are each priced as separate jobs.

## Questions about a humming house

### Is a steady mains hum dangerous?

A steady hum from a transformer is a part we test, and a harsh buzz with heat or a burning smell means that circuit stays off. We test the joint before it is used again. Book Now if the plastic is warm or you can smell burning.

### Will a new fuse board stop the hum?

A new fuse board stops the hum only when the tests show the board itself is vibrating or has a loose joint. A dimmer, a charger or a street transformer keeps humming on a new board. We price fuse board replacement on its own after those tests.

### Can you tell a dimmer hum from a loose joint?

Yes, a dimmer buzz changes as you move the dimmer, and it eases at full brightness. A loose joint keeps a harsh buzz under load and warms the fitting. We confirm which one it is with the circuit isolated.

### What paperwork follows a hum repair?

Where we alter the circuit, a minor works certificate records the tests and our NAPIT registration. If we only find that the street transformer is humming and we change nothing, we write down the readings and the part that hums. An EICR, the report on the whole installation, is a separate job.

### Do you open the fuse board on every hum?

We open the fuse board when the hum is at the board or the tests point inside it. A sound board stays shut. We leave the cover on until a tester shows that circuit is dead, and only then do we open it.

## Related problems
- [Automatic gate not opening](https://lightingelectrical.co.uk/problems/electric-gate-not-working): A gate that will not move has lost its supply, its safety beam or its motor control, so the outdoor circuit needs a test.
- [Buzzing sound in the wall](https://lightingelectrical.co.uk/problems/buzzing-in-walls): A buzz inside a wall is a loose joint, a dimmer or a damaged cable on that circuit.
- [Circuit breaker keeps tripping](https://lightingelectrical.co.uk/problems/circuit-breaker-keeps-tripping): The breaker keeps tripping because a fault is still on the circuit, in an appliance, a cable, a joint or the protective device.
- [Consumer unit tripping with nothing plugged in](https://lightingelectrical.co.uk/problems/consumer-unit-tripping-nothing-plugged-in): The consumer unit trips with nothing plugged in because fixed wiring or the safety switch is sending current to earth.
- [Downstairs circuit keeps tripping](https://lightingelectrical.co.uk/problems/downstairs-circuit-keeps-tripping): The downstairs breaker or RCD opens because a socket, light, cable or appliance on that floor is leaking or overloaded.
- [Driveway lights not working](https://lightingelectrical.co.uk/problems/driveway-light-not-working): Driveway lights go dark when the outdoor circuit, a sensor or a lantern fails, while rooms on another breaker stay lit.

## Sources
- [Electrical Safety First: Safety Guidance](https://www.electricalsafetyfirst.org.uk/guidance/)
- [BS 7671: IET Wiring Regulations (18th Edition)](https://electrical.theiet.org/bs-7671/)
- [Energy Networks Association: Power Cut Information](https://www.energynetworks.org/operating-the-networks/power-cuts)

Updated 2026-11-16.

[Electrical fault finding](https://lightingelectrical.co.uk/services/electrical-fault-finding)

## Book or ask a question
- [Book Now](https://lightingelectrical.co.uk/#chat)
