---
title: "Outside light not working | 4.7 Star · NAPIT approved · From £60"
description: "Outside light not working in Peterborough means we test the lamp, sensor and lighting circuit, then name the failed part before any fitting is changed."
canonical: "https://lightingelectrical.co.uk/problems/outside-light-not-working"
---

# Outside light not working

> Outside light not working in Peterborough means we test the lamp, sensor and lighting circuit, then name the failed part before any fitting is changed.

An outside light that stays off means the lamp, the sensor or the lighting circuit has failed. Lighting Electrical in Peterborough measures that lantern circuit and tells you the failed part.

## Why is my outside light not working?

An outside light stays off when the lamp, the sensor, the switch or the cable on that lighting circuit has failed.
- **The lamp or LED module has failed:** A lamp is the bulb inside the lantern. An LED module is the sealed light panel used where no bulb unscrews. When either one fails, that lantern stays dark and the other lights in the house stay on.
- **A PIR or a photocell is holding it off:** A PIR is a sensor that turns the lantern on when someone moves. A photocell is a daylight sensor that keeps the lantern off while it is still light. A stuck photocell or a dead PIR leaves the lamp dark after sunset.
- **The lighting breaker or RCD has opened:** A breaker is the switch in the fuse board for one circuit. An RCD is a safety switch that opens when current leaks to earth. Earth is the safe path for that fault current. The outside lights on that device go off together.
- **Water has entered the lantern or the gland:** A gland is the seal where the cable enters the lantern or an outdoor enclosure. Rain enters through a cracked cover or a loose gland and bridges the contacts. The lamp goes out, and the RCD can open as well.
- **The switch, timer or a joint has opened:** The wall switch or a timer can stop feeding the lantern while indoor lights on another switch stay on. A loose terminal on a lighting circuit that has been added to fails at that joint. The lantern then stays dark.

## What can I check on an outside light safely?

You can try a known lamp, test the sensor after dark, and read the lighting breaker with the fuse board cover shut.
- **A lamp you already know works:** Where the lantern lets you change the bulb by hand, fit that lamp and switch on. Leave a sealed LED lantern closed. Do not undo screws, the gland or the wall plate.
- **The PIR and the photocell after dark:** Wave a hand across the PIR once it is fully dark. If you can reach the photocell without a tool, cover it for a few seconds. A lantern that lights has a working lamp and a sensor that was keeping it off.
- **The lighting breaker behind a shut cover:** Look through the fuse board cover for the lighting breaker. Reset it once if the board is cool, quiet and has no burning smell. If the switch drops straight away, leave it down.
- **One lantern or every outside light:** Switch on each outside lantern and any soffit downlight on the same wall. One dark fitting points to that lamp, sensor or switch. All of them dark points to the breaker or the cable that feeds the group.

## When should I book for an outside light?

Book Now when a known good lamp stays dark, the lighting breaker will not hold, or the lantern is cracked, warm or wet.
- **A good lamp and the lantern stays dark:** The sensor, the switch or the cable is still open. Fitting more lamps will not close that gap. The outside light circuit needs a test with the power off.
- **The lighting breaker will not stay up:** The breaker opens when the outside light is turned on, even with no other change. Leave that breaker off. Another reset heats the terminals in the board.
- **A cracked, warm or wet lantern:** Cracked glass, brown marks or water on the inner glass means the seal has gone. Switch the lantern off at the wall switch or the breaker handle. Leave every screw in place.

## What happens on a visit for an outside light?

We start at the fuse board, test the outside light circuit, and name the failed part before a lantern or a cable is changed.
- **Which lantern failed and when:** We ask which outside light is dark, whether it failed after rain, and whether a PIR, a photocell or a timer controls it. We read the lighting breaker with you. The fuse board cover stays shut until that circuit is isolated.
- **Measurements on the lantern circuit:** We switch the lighting circuit off at its breaker. We measure from the board to the switch and on to the lantern. Those readings separate a dead lamp, a failed sensor, an open joint and a wet cable.
- **The gland, the sensor and the earthing:** We open only the lantern the readings point to, and we remake a gland that has let water in. Earthing, the fault path that opens the breaker, is checked on this circuit. Bonding, the link between metal pipes and the fuse board, is checked on the same visit. We also check that the supply can carry the outside lights before a further price.
- **The repair and the certificate:** We fit the failed lamp, sensor, switch or cable after you accept the repair. We test the circuit again. A minor works certificate follows when we alter the outside light circuit, and our NAPIT registration is on it. The breaker stays off if the circuit is unsafe to switch back on.

## What does an outside light fault cost?

Electrical Fault Finding & Repair is charged by the hour for this outside light. That price covers the tests, the diagnosis we give you, and the repair of the failed part once you accept it. A second fitting, a replacement sensor or a minor works certificate changes the price. Emergency electrician work is charged separately.
- Fault finding & repair: from £75 an hour
- One failed lamp is a shorter test than water tracking along an outdoor cable to a lantern.
- We fit a Varilight, MK Electric, BG Electrical, Hager, Wylex or Contactum part only after the test shows it has failed.
- A failed lighting breaker on the board is quoted afterwards as fuse board replacement.

## Questions about an outside light not working

### Will you change the lantern before finding the fault?

No. We measure the outside light circuit and tell you the failed lamp, sensor, switch or cable. We fit a replacement only after you accept it. A lantern that tests sound stays on the wall.

### Can rain on its own stop an outside light?

Yes. Water in a cracked lantern or past a loose gland leaks current to earth and can open the RCD. We test that fitting with the circuit switched off and remake the gland when the seal has failed.

### What paperwork do I get after the repair?

A minor works certificate is issued when we alter the outside light circuit. It lists the tests for that job and our NAPIT registration. An EICR, the Electrical Installation Condition Report, is a separate check of the whole installation.

### Will a new fuse board fix a dark outside light?

A new fuse board brings the light back only if the tests show the board has failed. A dead lamp, a stuck sensor or a wet gland stays dark on a sound board. We price fuse board replacement on its own when the board is the failed part.

### Is this the same as a new outside light installation?

No. A dark lantern is Electrical Fault Finding & Repair. Lighting Installation is the job for a new wall lantern or extra outside lights. That installation has its own price.

## Related problems
- [Automatic gate not opening](https://lightingelectrical.co.uk/problems/electric-gate-not-working): A gate that will not move has lost its supply, its safety beam or its motor control, so the outdoor circuit needs a test.
- [Buzzing sound in the wall](https://lightingelectrical.co.uk/problems/buzzing-in-walls): A buzz inside a wall is a loose joint, a dimmer or a damaged cable on that circuit.
- [Circuit breaker keeps tripping](https://lightingelectrical.co.uk/problems/circuit-breaker-keeps-tripping): The breaker keeps tripping because a fault is still on the circuit, in an appliance, a cable, a joint or the protective device.
- [Consumer unit tripping with nothing plugged in](https://lightingelectrical.co.uk/problems/consumer-unit-tripping-nothing-plugged-in): The consumer unit trips with nothing plugged in because fixed wiring or the safety switch is sending current to earth.
- [Downstairs circuit keeps tripping](https://lightingelectrical.co.uk/problems/downstairs-circuit-keeps-tripping): The downstairs breaker or RCD opens because a socket, light, cable or appliance on that floor is leaking or overloaded.
- [Driveway lights not working](https://lightingelectrical.co.uk/problems/driveway-light-not-working): Driveway lights go dark when the outdoor circuit, a sensor or a lantern fails, while rooms on another breaker stay lit.

## Sources
- [BS 7671: IET Wiring Regulations (18th Edition)](https://electrical.theiet.org/bs-7671/)
- [Electrical Safety First: Safety Guidance](https://www.electricalsafetyfirst.org.uk/guidance/)
- [NICEIC: Householder Guidance](https://niceic.com/householders/)

Updated 2026-11-16.

[Electrical fault finding](https://lightingelectrical.co.uk/services/electrical-fault-finding)

## Book or ask a question
- [Book Now](https://lightingelectrical.co.uk/#chat)
