---
title: "Security light not coming on | 4.7 Star · NAPIT approved · From £60"
description: "Security light not coming on in Peterborough. Lighting Electrical tests the lamp, the movement sensor and the outdoor circuit. We then name the failed…"
canonical: "https://lightingelectrical.co.uk/problems/security-light-not-working"
---

# Security light not coming on

> Security light not coming on in Peterborough. Lighting Electrical tests the lamp, the movement sensor and the outdoor circuit. We then name the failed…

A security light that stays dark has a failed lamp, sensor or outdoor circuit. Lighting Electrical tests that lantern in Peterborough. We name the part that failed.

## Why does a security light stay off?

A security light stays off when the lamp, the movement sensor or the supply to that fitting has failed. Indoor lights can stay on because the lantern has its own wall switch and often its own breaker.
- **The lamp has failed:** The lamp is the part that produces the light. A wall lantern may use a visible bulb or a sealed module that you cannot swap from outside. A dead lamp leaves the lantern dark even when the sensor still clicks.
- **The movement sensor has failed:** A PIR sensor is a passive infrared detector that watches for body heat moving across its view. A failed sensor never sends the lamp a signal to start. Paint on the lens, or a dial turned fully down, blocks that signal as well.
- **The daylight sensor is holding it off:** A photocell is a sensor that keeps the lamp off in daylight. A failed photocell can behave as if the sun is still up. A cap left on the lantern does the same, so the lamp never starts at night.
- **The outdoor breaker has opened:** A breaker is the switch in the fuse board that protects one circuit. It opens when the lantern or its cable draws a short or leaks to earth. Earth is the safety path that carries fault current away from you. With the breaker down, the lantern has no power.
- **Water has entered the lantern:** Rain gets in through a cracked cover or a loose gland. A gland is the seal where the cable enters the fitting. Damp on the lamp terminals stops the lamp lighting. The same damp can open the breaker.

## What can I check on a security light safely?

You can move the wall switch. You can read the fuse board through the closed cover. You can wipe the outside of the lens. The lantern stays shut.
- **The wall switch position:** Switch the indoor control fully off. Wait a few seconds. Switch it on again. Many lanterns use that pause to return to automatic mode. A second switch left off keeps the lantern dark.
- **One look at the breaker:** Find the breaker for outside lights by reading the names through the closed cover. Reset it once only if the fuse board is cool, quiet and free of any burning smell. If it opens again, leave it down.
- **Dirt on the sensor lens:** Cobwebs, dust or a plastic film stop the sensor seeing you. Wipe the outside of the lens with a dry cloth. Leave every screw in the lantern.
- **A walk past after dark:** Daylight can keep a healthy lantern off, so try it when the sky is dark. Walk across the front of the fitting. If it still stays dark, the lamp, the sensor or the circuit needs a test.

## When should I book for a security light that stays off?

Book Now if the lantern stays dark after the safe checks, the breaker will not hold, or the fitting is cracked, wet or hot.
- **Still dark after the safe checks:** The switch is on and the breaker is up. The lens is clean and the sky is dark. The lantern still never lights. The fault is in the fitting or the cable, so Book Now.
- **The breaker will not stay up:** The outdoor breaker opens as you walk past the lantern. It may also open straight after a single reset. Leave it off. The short or the leak to earth needs a test.
- **Cracked, wet or smelling of burning:** A cracked cover lets rain onto the lamp. Brown marks or a burning smell mean a joint is overheating. Switch the lantern off at the wall. Keep your hands off the wet fitting.

## What happens on a security light visit?

We isolate the outdoor circuit and test the lantern. We name the failed lamp, sensor or cable before anything is changed.
- **What you tell us about the lantern:** We ask which lantern stays dark. We ask when it last lit. We ask what the wall switch does now. We read the outdoor breaker beside you while the fuse board cover stays shut.
- **Dead tests on the fitting and cable:** We switch the outdoor circuit off and prove the lantern is dead. We test the lamp, the PIR sensor, the photocell and the cable to the board. The results show whether the lamp, the sensor or the cable has failed.
- **A named fault before any fitting is changed:** We tell you the failed part before a lamp, a sensor or a lantern is changed. A fitting that tests sound stays on the wall. We check earthing, which is the fault path back to the board. We check bonding, which links metalwork to that path. We check that the supply can carry the outdoor load before we write any further price.
- **Repair of the failed part:** The failed lamp, sensor, joint or lantern is changed when you accept the work. We test the circuit again after that change. A minor works certificate records the alteration and our NAPIT registration when the circuit was changed. The breaker stays off if the circuit cannot be left on.

## What does a security light fault visit cost?

Electrical Fault Finding & Repair is charged by the hour. The hour covers the tests on the dark lantern. It also covers the diagnosis we give you. It also covers the repair of the failed part when you accept the work. A lamp change takes less time than a break in the outdoor cable. A whole lantern is priced as Lighting Installation. A minor works certificate is added when the circuit is altered. Emergency electrician attendance is priced as its own job.
- Fault finding & repair: from £75 an hour
- A lamp, a sensor or a lantern is fitted only after tests show it has failed.
- Lighting Installation is a separate price when the whole lantern is replaced.
- Emergency electrician attendance is separate from the hourly fault finding.

## Questions about a security light that stays off

### Will you replace my security light before finding the fault?

No. We test the lamp, the sensor and the cable first. We name the failed part before anything is changed. A lantern that tests sound stays on the wall.

### Can I fit a new bulb myself?

Leave the lantern shut. A sealed module is not a bulb you can swap from the outside. We test the lamp with the circuit switched off and fit a new lamp only when that test shows it has failed.

### Why is my security light off in the daytime?

The photocell is doing its job while the sky is bright. The lamp is meant to wait until dark on this type of lantern. If it also stays dark at night, the lamp, the sensor or the circuit needs a test.

### Will I get a certificate after the repair?

A minor works certificate is issued when the repair alters the circuit. It records the tests and our NAPIT registration. If nothing is changed, we still tell you the readings and the failed part.

### What if the lantern trips the breaker?

Current is leaking to earth in the lantern or its cable. The breaker opens as the lamp tries to start. Leave that breaker off so we can test the fitting and name the leak.

## Related problems
- [Automatic gate not opening](https://lightingelectrical.co.uk/problems/electric-gate-not-working): A gate that will not move has lost its supply, its safety beam or its motor control, so the outdoor circuit needs a test.
- [Buzzing sound in the wall](https://lightingelectrical.co.uk/problems/buzzing-in-walls): A buzz inside a wall is a loose joint, a dimmer or a damaged cable on that circuit.
- [Circuit breaker keeps tripping](https://lightingelectrical.co.uk/problems/circuit-breaker-keeps-tripping): The breaker keeps tripping because a fault is still on the circuit, in an appliance, a cable, a joint or the protective device.
- [Consumer unit tripping with nothing plugged in](https://lightingelectrical.co.uk/problems/consumer-unit-tripping-nothing-plugged-in): The consumer unit trips with nothing plugged in because fixed wiring or the safety switch is sending current to earth.
- [Downstairs circuit keeps tripping](https://lightingelectrical.co.uk/problems/downstairs-circuit-keeps-tripping): The downstairs breaker or RCD opens because a socket, light, cable or appliance on that floor is leaking or overloaded.
- [Driveway lights not working](https://lightingelectrical.co.uk/problems/driveway-light-not-working): Driveway lights go dark when the outdoor circuit, a sensor or a lantern fails, while rooms on another breaker stay lit.

## Sources
- [Electrical Safety First: Safety Guidance](https://www.electricalsafetyfirst.org.uk/guidance/)
- [HSE: Electrical Safety at Work](https://www.hse.gov.uk/electricity/)
- [NICEIC: Householder Guidance](https://niceic.com/householders/)

Updated 2026-11-16.

[Electrical fault finding](https://lightingelectrical.co.uk/services/electrical-fault-finding)

## Book or ask a question
- [Book Now](https://lightingelectrical.co.uk/#chat)
