Automatic gate not opening
An automatic gate that stays shut has lost its supply, its safety beam or its motor control. Lighting Electrical tests the outdoor circuit for this fault from Peterborough and names what failed.
Calls answered 24/7
- 10 years trading
Why will an automatic gate not open?
An automatic gate stops because the outdoor supply, the safety beam or the motor control has failed. We test those electrical parts on the visit.
- The outdoor breaker has openedThe gate is usually on its own breaker or RCD in the fuse board. Rain in a cable gland or a cut in the armoured cable lets current leak to earth. Earth is the path that carries a fault away from you. The breaker opens and the motor loses power.
- The safety beam is blocked or blindA safety beam is a sender and a receiver aimed across the drive. Dirt, a bin or a bad aim breaks that beam. The control then treats the drive as blocked. Many gates then refuse to close. Some controls refuse every move until the beam is restored.
- The limit switch still says openA limit switch tells the control that the leaf has finished opening or closing. A stuck switch keeps sending the open signal. The control will not start another open run. The leaf stays where it is.
- The manual release is still onA manual release uncouples the motor from the leaf so the gate can be pushed by hand. Left on, the motor can run while the leaf does not move. We check that release before any motor part is blamed.
- The motor hums and does not turnA gate motor on a house supply uses a capacitor to start turning. A failed capacitor leaves a hum and a still leaf. A blown fuse on the control board stops the motor with the leaf unmoved.
- Water in the outdoor enclosureThe control often sits in an outdoor box fed by armoured cable. Water across the terminals trips the supply or burns a joint. The house lights stay on on their own circuit. The gate stays still.
What can I check on a stuck electric gate?
You can check the fuse board, the remote, the safety beams and a known lamp while every cover stays on. You do not open the gate box and you do not touch the wiring.
- The gate switch with the cover shutLeave the fuse board cover on. Read the breaker named for the gate, the garage or the outside sockets. If that switch is down and the board is cool, quiet and free of any burning smell, one reset is reasonable. If it opens again at once, leave it off.
- The wall button and the remotePress the button fixed by the door as well as the handset. Movement from the wall button only points to the remote. You can fit a fresh battery in the handset. The control box stays shut.
- A clear line between the safety beamsLook along the two small eyes beside the drive. Wipe the faces and move leaves, a bin or a parked car out of the line. You leave the eyes and their cables alone. A clear line with a gate that still will not move needs a test.
- A lamp in a nearby outdoor socketIf a weatherproof socket sits on the same outside wall, plug in a lamp you already trust. A dead lamp beside a dead gate points to the outdoor supply. A lit lamp means the gate control needs the test. Leave the socket cover closed.
When should I book for a gate that will not move?
Book Now when one reset will not hold, the motor hums without moving the leaf, or the outdoor box is hot, wet or smelling of burning.
- The gate switch drops straight awayPortable plugs on that outdoor circuit are out and the switch still opens at once. The fault sits in the cable, the enclosure or the motor. Another reset heats the terminals. Leave that switch off.
- The motor hums and the leaf stays putA hum with no movement means power is at the motor and the leaf is not being driven. Forcing the leaf can strip the drive. Leave the gate as it stands.
- Heat, water or a burning smellA warm enclosure, a buzz or brown marks mean a joint is failing. Rain running into the box can hold the supply off. Use the breaker handle to switch that circuit off. Keep your hands off the lid screws.
What happens on a visit for a gate that will not move?
We test the gate supply and the control in order and name the failed part before any cable or device is changed.
- What the gate does and which switch openedWe ask whether the leaf is dead, humming or stopping part way. We ask if the wall button and the remote behave differently. We read the outdoor breaker with you while the fuse board cover stays on.
- Meter tests on the supply and the beamWe switch the gate circuit off and confirm it is dead with a tester. We measure the outdoor cable and the beam circuit. The readings separate a tripped breaker, a wet joint, a blind beam and a motor that will not turn.
- The failed part named before a replacementWe tell you the failed part before a photocell, a capacitor, a joint or a length of cable is changed. We check the earth path on the outdoor cable, which is what lets a breaker open on a fault. We also check the bond on metalwork that should join that earth.
- Repair after you say yesWe fit the failed part only after you say yes. We test the circuit again after that work. Where the circuit was altered we issue a minor works certificate under our NAPIT registration. If the circuit is unsafe to put back on, we leave that breaker off.
What does tracing a dead electric gate cost?
You pay for the hour we spend on the gate supply and the control. The hour includes meter tests, a spoken account of what failed, and the first repair work after you say yes. A long armoured cable back to the fuse board takes more of that hour than a wet joint in the outdoor box. Fitting a part, or writing a minor works certificate, changes what you pay.
From £75 an hour
Included when agreed
- Testing at the board and along the failed circuit until the cause is named
- A spoken diagnosis before any part is swapped
- Repair of the failed joint, accessory, cable or protective device once you accept the hourly work
- Making the circuit safe if it cannot be left live that day
- A minor works certificate when the repair needs one
Not included automatically
- A full house rewire or a new consumer unit as the first step
- Solar, battery, EV charger or forklift charger work
- Guesswork replacement of parts that have not failed
Ways to pay


- Pay by bank
- Bank transfer
- A photocell, capacitor, breaker or short armoured cable is fitted after the readings name that part.
- The minor works certificate records a circuit we have altered and shows our NAPIT registration.
- Testing each joint on a long armoured cable takes more time than a wet terminal in the outdoor box.
How booking works
Tell us about the job
Tap Book Now and describe the work in the chat. Photos help.
Get your price
You see your price in the chat. A set price is paid at checkout; any other job is quoted first.
Choose your visit
Give your address and when you are free, and the visit is arranged.
Why choose Lighting Electrical
We work with Hager, Wylex, Contactum, BG Electrical, MK Electric, Varilight, myenergi, Ohme, Hypervolt, Andersen, Aico, FireAngel and Mira.
- Reviews
- 61
- Rating
- 4.7
- Trading since
- 2016
“Ten years on Colchester housing stock and I have seen most of it: terraces where the lighting circuit has been extended once too often, boards fitted before RCDs were standard, new builds with sockets nowhere near the kitchen. I check the earthing, the bonding and whether the supply will carry another load before I price anything, because the age of a house settles nothing on its own.”
Valandi Kotorri, Lighting Electrical
Book NowWill you change the gate motor before you find the fault?
No. We test the supply, the safety beam and the control and name the failed part first. A motor that still tests sound stays on the gate. We fit a new motor only after you say yes and only when the readings show it has failed.
Can I put the gate into manual release to get my car out?
Yes, if the gate has a householder release and you can work it without opening the control box. Switch the outdoor breaker off first, then use the release as the gate maker intends so the leaf can be moved by hand. If no release is visible, or the leaf is jammed, leave it and Book Now.
Why is the gate dead when the house lights are on?
The gate is fed from its own breaker, often beside the outside sockets, so a fault there leaves the lights on. We test that outdoor circuit and name the part that stopped the motor. The lighting circuit stays as it is.
What paper do I get after a gate repair?
A minor works certificate follows when we alter the circuit, and it carries the test results and our NAPIT registration. When the fault is only a blind safety beam or a spent fuse in the control, the house circuit stays as we found it. We still tell you the readings and the part that failed.
Related problems
- Buzzing sound in the wallA buzz inside a wall is a loose joint, a dimmer or a damaged cable on that circuit.
- Circuit breaker keeps trippingThe breaker keeps tripping because a fault is still on the circuit, in an appliance, a cable, a joint or the protective device.
- Consumer unit tripping with nothing plugged inThe consumer unit trips with nothing plugged in because fixed wiring or the safety switch is sending current to earth.
- Downstairs circuit keeps trippingThe downstairs breaker or RCD opens because a socket, light, cable or appliance on that floor is leaking or overloaded.
- Driveway lights not workingDriveway lights go dark when the outdoor circuit, a sensor or a lantern fails, while rooms on another breaker stay lit.
- Electric boiler trips the electricsAn electric boiler trips the electrics when its circuit leaks to earth or draws more current than its breaker allows.
Sources
- BS 7671: IET Wiring Regulations (18th Edition)
- HSE: Electrical Safety at Work
- Electrical Safety First: Safety Guidance
Updated 16 November 2026
