Andersen

Andersen EV chargers in Peterborough

Lighting Electrical fits and repairs Andersen A2 and A3 EV chargers in Peterborough, setting each one up in the Konnect+ app and leaving it on its own tested circuit.

Calls answered 24/7

  • 10 years trading

Andersen A2 and A3 chargers we install and fix

Andersen makes home chargers for electric cars, controlled through its Konnect+ app. We mount new Andersen units, move existing ones, trace their faults and check them over, and each charger runs from a circuit of its own.

  • Andersen A2, tethered or with a socketThe A2 comes with a fixed lead or a Type 2 socket for your own cable. On the tethered version the lead winds round the body for storage, so we leave clear wall space on each side. Its front panel comes in a range of colours and wood finishes.
  • Andersen A3 and the load sensorThe A3 is a slimmer Andersen unit run from the same app. With either model we clip a load sensor round the meter tails, the thick cables between meter and board, so the charger eases off when the house draws heavily.
  • Andersen faults we put rightAn Andersen shows no numbered codes on the unit. The status light colour and the message in Konnect+ tell us where to start. We fix units that drop offline, cut out on a PEN fault, which is a broken neutral and earth in the street cable, trip their breaker as a charge begins or have a damaged lead.
  • What an Andersen service coversWe check the panel seals and cable gland for water, look over the lead and connector for wear, and test the breaker and earth leakage protection feeding the unit. Then we confirm the sensor reading and the firmware version in the app.

Andersen’s website

What happens to an Andersen charger in each service

EICR testing in Peterborough

EICR

from £150

The Andersen circuit is tested with the rest of the fixed wiring. We check its breaker, its earth and the cable out to the unit, and note whether the charger's built in PEN fault cut out lets it run without an earth rod.

Fuse board replacement

Consumer unit replacement

from £450

A new board gives the Andersen its own way on an RCBO, a breaker with earth leakage protection built in. We refit the load sensor on the meter tails and confirm the unit comes back online in Konnect+.

House rewiring in Peterborough

House rewiring

from £2,400

If the Andersen feed tests sound, the rewire keeps it and lands it on a marked way in the new board. With floors up, it is the easy moment to run a fresh feed if the charger should sit nearer the drive.

Electrical fault finding

Electrical fault finding

from £75 an hour

When an Andersen will not start a charge, we read the status light and the app message first. Then we measure the supply, the earth and the circuit to show whether the fault lies in the unit, the cable or the car.

Lighting installation

Lighting installation

from £65

Lighting work leaves the Andersen alone. A drive or porch light beside the charger runs from a lighting circuit and never from the charger feed, so a lamp fault cannot stop a charge.

EV charger installation

Andersen EV charger installation

from £750

This is the main Andersen job. We check the main fuse and earthing, mount the A2 or A3 at the parking spot on a dedicated circuit, fit the load sensor and link the charger to Konnect+ before a test charge.

Socket and switch installation

Socket installation

from £85

An Andersen is wired in and takes no plug. A weatherproof socket by the drive for garden tools goes on a separate circuit with RCD protection and is never spurred off the charger cable.

Emergency electrician

Emergency electrician

from £90 an hour

An Andersen that smells hot, shows scorching or trips the board out of hours is switched off at its breaker and local isolator. The house goes back on and the charger stays off until its circuit has been tested.

Electrical testing and certificates

Electrical testing and certificates

from £95

PAT testing covers items with a plug, so a fixed Andersen is not on the list. The three pin charging lead that came with the car can be tested on the same visit and added to the record.

Fire and smoke alarm installation

Smoke alarm installation

from £110

Smoke and heat alarms do not connect to an Andersen. Where the car charges inside a garage joined to the house, we fit a heat alarm in there and link it to the alarms indoors.

Appliance and heating connections

Appliance and heating connections

from £120

Before a cooker or heater is connected, we check the main fuse can carry it while the Andersen is charging. The load sensor then lets the charger ease back whenever the kitchen is busy.

Solar and battery storage

Solar panel and battery storage installation

from £5,500

The inverter and the Andersen each run from a separate circuit. We place the sensor so the charger reads what the house actually takes from the grid once the panels generate, and label the board for both supplies.

Forklift charger installation

Forklift charger installation

from £700

Forklift chargers are warehouse plant, not Andersen units. We fit them on their own circuit and isolator at the bay, kept apart from any Andersen serving a staff parking space.

Commercial lighting installation

Commercial Lighting Installation

from £65

Where a business has an Andersen in its car park, new lighting goes on its own breakers at the distribution board. The charger keeps its dedicated way, so a lighting fault never cuts a charge.

Starlink installation

Starlink installation

from £350

We mount the dish and set up the router, and no Andersen parts are involved. If the charger keeps dropping out of Konnect+, we check whether the new router position reaches the charger wall.

Light switch or dimmer replacement

Light switch or dimmer replacement

from £60

A switch or dimmer swap involves no Andersen equipment. Only the lighting breaker goes off, so a timed charge set in the app carries on while the new control is fitted.

Minor works certificate

Minor works certificate

from £95

Moving the isolator or lengthening the feed to an Andersen is a small change to an existing circuit. We test that circuit and write the breaker rating, the change and the readings on the certificate.

Extractor fan installation

Extractor fan installation

from £180

A fan has no link to an Andersen. It takes power from the lighting circuit or a fused spur, a switched outlet with its own fuse, and the charger feed is never touched.

Electric shower installation

Electric shower installation

from £220

A shower and an Andersen are two heavy loads on one supply. Before fitting the shower, we check the main fuse covers both and that the load sensor slows the charger whenever the shower runs.

Emergency lighting test & certificate

Emergency lighting test & certificate

from £150

Emergency lighting uses no Andersen parts. At a workplace with Andersen bays, only the emergency fittings lose mains during the test, so cars parked on charge keep charging.

Immersion heater repair

Immersion heater repair

from £70 an hour

An immersion repair leaves the Andersen alone. We isolate just the immersion circuit, test the element and thermostat and replace the failed part, while the charger stays live.

Battery storage installation

Battery storage installation

from £4,500

A home battery changes what the sensor on the meter tails reads. We fit the battery on its own way and position the sensors so the Andersen follows grid demand rather than draining the battery into the car.

Fire alarm system installation

Fire alarm system installation

from £1,400

A fire alarm panel uses no Andersen parts. It takes its own marked breaker, kept clear of any charger circuit in the building, so switching off one never affects the other.

Cherry picker hire

Cherry picker hire

Cherry picker hire involves no Andersen equipment, as the charger sits at wall height. The machine comes with an electrician to operate it for lights, signs and fittings high up.

Why is my Andersen charger off with the rest of the house?

  • No power in the whole houseAn Andersen goes dark along with everything else in a full outage. We check the main switch, the RCDs and the street supply, switch the charger breaker on last and confirm the unit reconnects to Konnect+.

Other brands we work on

How booking works

  1. Tell us about the job

    Tap Book Now and describe the work in the chat. Photos help.

  2. Get your price

    You see your price in the chat. A set price is paid at checkout; any other job is quoted first.

  3. Choose your visit

    Give your address and when you are free, and the visit is arranged.

Follow your job from booking to receipt

See when we're on our way, get your job report the moment we finish, and pay in seconds.

  • Track us on our way

    See us on the map with a live arrival time.

  • Your job report, same day

    See exactly what was done as soon as we finish.

  • Invoice and receipt in one place

    Pay online in seconds, and your receipt is always there when you need it.

Why choose Lighting Electrical

Photo of Valandi KotorriValandi KotorriElectrician
Reviews
61
Rating
4.7
Trading since
2016
“Ten years on Colchester housing stock and I have seen most of it: terraces where the lighting circuit has been extended once too often, boards fitted before RCDs were standard, new builds with sockets nowhere near the kitchen. I check the earthing, the bonding and whether the supply will carry another load before I price anything, because the age of a house settles nothing on its own.”

Valandi Kotorri, Lighting Electrical

Book Now

Andersen EV charger questions

Still have a question?

Can you fit a tethered Andersen A2 with the cable wrapped round it?

Yes. The tethered A2 stores its lead by winding it round the body, so we mount it with space on each side for that. It goes on a dedicated circuit and is tested before the first charge.

Does an Andersen charger need an earth rod?

Usually not. Andersen chargers include PEN fault protection, which stops the charge if the combined neutral and earth in the street cable fails. We test the earthing at the meter before confirming it for your supply.

Why has my Andersen dropped out of the Konnect+ app?

The charger has lost its internet link, often from weak wifi at the wall or a changed router password. We check the signal at the unit and test the circuit, then link the charger to the app again.

Can you move my Andersen charger to another wall?

Yes. We take the unit down, make the old feed safe and run a new circuit to the new spot. The charger is tested again and relinked in Konnect+ before you use it.

Will my fuse board take an Andersen charger?

It needs a spare way and a main fuse that can carry the charger alongside the rest of the house. The load sensor lets the Andersen slow down when the house is busy, which often avoids a supply upgrade. A full board is priced as a separate job.

Book or ask a question

Calls answered 24/7