Brown marks on a socket or plug
Scorch marks on a socket or plug mean a connection has overheated. Lighting Electrical in Peterborough switches that circuit off. We test the socket before anyone uses it again.
Calls answered 24/7
- 10 years trading
Why do sockets and plugs show scorch marks?
Scorch marks show that a connection at the socket or inside the plug has run hot enough to brown or blacken the plastic.
- A loose terminal behind the socketThe screws that clamp the cable work loose. A loose joint resists the current. That resistance turns into heat and browns the plastic around the pin holes.
- Socket contacts that no longer gripEach pin should sit tight in a brass contact. Worn contacts spark under load. That sparking is called arcing, and it chars one pin hole more than the others.
- Too much load on one socketA heater or a kettle draws a heavy current through one set of pins. Stacking those loads in an adaptor heats the pins. The socket face browns around the holes that carried the current.
- A damaged plug or a loose fuseThe fuse is the small wire link inside a UK plug that opens on too much current. A loose fuse holder or bent pins heat the plug top. Brown marks on the plug, with a clean socket, start in the plug.
- A plug left half insertedPins that do not go fully home touch only a small part of the contact. That small area heats under load. The scorch sits at the mouth of the pin hole and on the face of the plug.
What can I check on a scorched socket?
You can compare the plug with the socket face and switch the circuit off at the fuse board. You leave every cover screwed shut.
- Whether the plug or the socket is markedUnplug the lead only when the plastic is cool to the back of your hand. Brown plastic on the plug with a clean socket points to the plug. Brown pin holes point to the socket contacts.
- Heat, smell and melted plasticStand back and look. A warm face, a burning smell or shiny melted plastic means the joint is still hot. Leave the plug in place and use the switch on the socket if it has one.
- The breaker for that roomA breaker is the switch on the fuse board that guards one circuit. Switch off the breaker named for those sockets if you can read the name through the closed cover. Leave the cover screws alone.
- What was plugged inNote the appliance that was in the socket, such as a heater or a kettle. Unplug other leads on that circuit only where the plastic is cool. Keep extension leads out of the scorched socket.
When should I book for scorch marks?
Book Now as soon as you see brown or black marks on a socket or a plug. That connection has already overheated.
- Brown or black marks around the pin holesThe marks mean the contacts have been hot. Using the socket again makes the joint hotter. Switch the circuit off and Book Now.
- A burning smell or soft plasticSmell and melted plastic mean the heat has reached the cable insulation. Keep your hands off the face. The circuit stays off until we test it.
- A scorched plug you still needA scorched plug heats the next socket it enters. Stop using that plug. Book Now so we can test the socket it last sat in.
What happens on a visit for scorch marks?
We isolate the marked socket, test the connection, and name the failed part before we replace anything.
- The plug, the socket and the fuse boardWe look at the marks with you and ask what was plugged in. We switch off the circuit at its breaker. A tester confirms the socket is dead before any screw comes out.
- Tests on the heated connectionWe test the socket terminals and the cable that feeds them. The readings show a loose joint, worn contacts, a failed plug, or heat damage further along the cable. We tell you which of those it is.
- Earthing and the load on the supplyEarthing is the path that lets fault current trip a breaker. Bonding is the link that joins metal pipes to that earth. We check both, and we check that the supply can carry the load, before we price any further work.
- The repair and the certificateThe failed socket or the damaged cable is replaced after you accept the repair. We test the circuit again. Where we alter the circuit, the finished tests go on a minor works certificate that carries our NAPIT registration.
What does a scorched socket visit cost?
The emergency electrician price covers our attendance, the tests on the scorched socket or plug, and making that circuit safe to leave. A new socket, a length of cable, or more time spent tracing heat along the cable changes the price. We write the extra price down before that work starts.
From £90 an hour
Included in the call-out
- Attendance at the property in Peterborough or a nearby Essex town
- Isolation of the failed circuit, fitting or board
- Fault finding on the circuit that has gone down
- Temporary making safe so the rest of the installation can be used where that is possible
- A written note of what failed and what work should follow
Not included automatically
- A full house rewire or a planned consumer unit replacement on the same visit unless already quoted
- Parts we do not carry in the van, which we price in writing before we fit them
- Work on another trade such as gas, plumbing or structural fabric
Ways to pay


- Pay by bank
- Bank transfer
- A cool plug with a burnt pin takes less time than a joint that has heated the cable inside the wall.
- A socket from MK Electric, BG Electrical or Contactum is added only when the test shows that socket has failed.
- Further repair that we have not priced in writing waits until you have accepted that price.
How booking works
Tell us about the job
Tap Book Now and describe the work in the chat. Photos help.
Get your price
You see your price in the chat. A set price is paid at checkout; any other job is quoted first.
Choose your visit
Give your address and when you are free, and the visit is arranged.
Why choose Lighting Electrical
We work with Hager, Wylex, Contactum, BG Electrical, MK Electric, Varilight, myenergi, Ohme, Hypervolt, Andersen, Aico, FireAngel and Mira.
- Reviews
- 61
- Rating
- 4.7
- Trading since
- 2016
“Ten years on Colchester housing stock and I have seen most of it: terraces where the lighting circuit has been extended once too often, boards fitted before RCDs were standard, new builds with sockets nowhere near the kitchen. I check the earthing, the bonding and whether the supply will carry another load before I price anything, because the age of a house settles nothing on its own.”
Valandi Kotorri, Lighting Electrical
Book NowCan I keep using a socket with brown marks?
No. Brown marks mean the connection has been hot, and further use heats it again. Switch that circuit off at the breaker and leave the socket unused until we test it.
Should I pull out a plug that looks scorched?
Pull it only when the plastic is cool. If the plug or the socket face is warm, leave it in place and switch the circuit off at the fuse board. We separate a burnt plug from a burnt socket on the visit.
Will you replace the socket on the same visit?
We replace the socket on the visit when the tests show it has failed and you accept the repair. A sound socket stays in place and we change the plug or the cable that failed. We test the circuit again before we leave it on.
Can the rest of the house stay on?
Yes. We switch off the circuit that feeds the scorched socket. Circuits on other breakers stay on. We put the repaired circuit back on only after the tests pass.
What paperwork do I get after the repair?
A repair that changes the circuit comes with a minor works certificate. The certificate records the tests and our NAPIT registration. If we only isolate the circuit and change nothing, you get a written note of the readings and the failed part.
Related problems
- Burning plastic smell from electricsA burning plastic smell means the insulation on a live joint is getting hot, so that circuit stays switched off until it is tested.
- Burning smell from a socketA burning smell from a socket means a connection is overheating and that circuit should stay off until it is tested.
- Burning smell from the fuse boxA burning smell at the fuse box means a connection or device is overheating, so that circuit stays off until it is tested.
- Electric shock from a light switchA shock from a light switch means the switch face is carrying current and that lighting circuit should be isolated.
- Electric shock from the showerA shock from the shower means current is on the water, the case or the taps, so that circuit stays off until it is tested.
- Electrical arcing or crackling soundA crackling noise is a spark at a loose or burnt joint, so that circuit stays off until it is tested.
Sources
- HSE: Electrical Safety at Work
- Electrical Safety First: Safety Guidance
- BS 7671: IET Wiring Regulations (18th Edition)
Updated 16 November 2026
