
Varilight light switches and dimmers in Peterborough
Lighting Electrical fits and replaces Varilight dimmers and light switches in Peterborough, setting each dimmer's lowest brightness level to suit the LED lamps it controls.
Calls answered 24/7
- 10 years trading
Which Varilight dimmers and switches do we fit?
We fit Varilight dimmers, light switches and matching plates, and repair the controls already on your walls. A dimmer is the wall control that sets how bright the lights are, and most of the work is matching it to the lamps it runs.
- Varilight LED dimmersVarilight builds dimmer modules for LED lamps. Most work as trailing edge dimmers, which trim the end of each mains cycle and suit the small drivers inside LED lamps. We add up the lamp wattage on the switch and check it sits inside the module's rated range before fitting.
- Two way and multipoint dimmingA landing or long room can have a dimmer at each end. Varilight does this with one master dimmer and a secondary unit at each other switch. We wire them through the cables already linking the switches where those cables suit, so every point dims the same lights.
- Faults we fix on Varilight controlsVarilight dimmers show no fault codes. The faults we fix are LED lamps that flicker at low settings, a dimmer that hums, lamps that glow faintly when switched off, a dimmer that cuts out when it runs hot, and cracked or loose plates.
- What servicing a Varilight dimmer involvesThere are no parts inside to service. We take the plate off, tighten the terminals and check the back box, the box in the wall behind the plate, leaves the module room to shed heat. If lamps have been changed, we reset the lowest brightness level to suit them.
What happens to Varilight controls in each electrical job?
EICR
from £150
Varilight dimmers and switches are part of the fixed wiring the report covers. We open a selection of plates, check each dimmer module for scorching and confirm metal plates are earthed. Anything loose or damaged gets a code on the report.
Consumer unit replacement
from £450
Your Varilight controls stay on the wall while the consumer unit changes. Afterwards we switch each lighting circuit back on one at a time and check every Varilight dimmer and switch works from its marked breaker.
House rewiring
from £2,400
New lighting circuits end at the wall controls. If you choose Varilight, we fit its switches or dimmers on new back boxes deep enough for the dimmer modules, with a neutral run to each switch position, which many Varilight dimmers need.
Electrical fault finding
from £75 an hour
Flicker or a faint glow on a Varilight dimmer can come from the dimmer, the lamps or a loose joint. We test the circuit and fit a plain switch for a short trial to see whether the dimmer is the cause before replacing it.
Varilight lighting installation
from £65
New lights get a matching control on the wall. We total the wattage of the new fittings, pick a Varilight dimmer module rated for that load, then set its lowest level once the lamps are lit.
EV charger installation
from £750
A charge point involves no Varilight switches or dimmers. We fit the charger on its own circuit from the consumer unit, with its own isolation and protection, and test it before handover.
Socket installation
from £85
We fit Varilight light switches, grid switches and sockets in the plate finish you pick, so every control in the room matches. Each back box is checked for depth and each metal plate for an earth before it goes on.
Emergency electrician
from £90 an hour
A Varilight dimmer that smells of burning, buzzes loudly or is too hot to touch gets its lighting circuit isolated out of hours. A replacement module follows once the cause is clear.
Electrical testing and certificates
from £95
PAT testing covers plug in appliances and lamps, not wall dimmers. We test and record each portable item, and the Varilight controls on the walls are checked under an EICR instead.
Smoke alarm installation
from £110
Mains smoke and heat alarms must never run through a Varilight dimmer. Where alarms take power from a lighting circuit, we connect them ahead of any dimmer so each alarm gets full mains.
Appliance and heating connections
from £120
Cookers, ovens and heaters use a heavy duty isolating switch, not a Varilight light control. We check the circuit can carry the appliance, connect it and test the circuit.
Solar panel and battery storage installation
from £5,500
Solar panels, inverters and batteries involve no Varilight parts. We fit the panels, inverter and isolation, connect the battery where it is part of the job, and test the new circuits.
Forklift charger installation
from £700
A forklift charger is commercial plant with no Varilight controls. We fit the charger and its isolator on a circuit for the bay and test the installation.
Commercial Lighting Installation
from £65
Shops and offices often want one plate to run several banks of lights. We fit Varilight grid switches and dimmer modules on a single plate, label each module with the area it controls, and size each dimmer for its bank of fittings.
Starlink installation
from £350
Starlink equipment uses no Varilight parts. We mount the dish, run and seal the cable and set up the router, adding a socket on an existing circuit if the router has none nearby.
Light switch or dimmer replacement
from £60
This is the main Varilight job. We isolate the lighting circuit, take off the old control and fit a Varilight switch or dimmer on the existing back box. Each dimmer is checked against the lamp load and set to a lowest level the lamps hold without flicker.
Minor works certificate
from £95
Changing a plain switch for a Varilight dimmer, or adding a lighting point, is a small alteration to an existing circuit. We test that lighting circuit and record the new control, its position and the readings on the certificate.
Extractor fan installation
from £180
A fan motor needs full mains, so it never goes on a dimmer. We wire the fan from the lighting circuit or a fused spur, a switched outlet with its own fuse, and keep it clear of any Varilight dimmer in the room.
Electric shower installation
from £220
An electric shower needs a heavy duty pull cord or double pole switch, not a Varilight light control. We fit the shower, its circuit and its isolation switch, then test the circuit once connected.
Emergency lighting test & certificate
from £150
Emergency fittings must not rely on a dimmer to light. We cut the mains to those fittings, time each battery and certify the result, while Varilight controls on other circuits stay on.
Immersion heater repair
from £70 an hour
The immersion runs through a 20 amp double pole switch by the cylinder, not a Varilight control. We test the element and thermostat, replace the part that failed and check that switch for heat damage.
Battery storage installation
from £4,500
A home battery uses no Varilight parts. We fit the battery and its inverter on their own protected circuit, isolate the connection while working and test it before handover.
Fire alarm system installation
from £1,400
A fire alarm panel takes a dedicated mains feed and no Varilight controls. We wire the panel, detectors, call points and sounders, then commission each device.
Cherry picker hire
Cherry picker hire involves no Varilight equipment. We bring the machine, set it up on firm ground and operate it for work at height such as high lights and signs.
Can a Varilight dimmer cause no power in the whole house?
- No power in the whole houseRarely on its own. A dimmer module that fails short can trip the RCD, the device that cuts power when current leaks to earth, and where one RCD covers several circuits most of the house goes dark. We check the main switch and RCDs, then test the lighting circuit if the trip follows the dimmer.
Other brands we work on
How booking works
Tell us about the job
Tap Book Now and describe the work in the chat. Photos help.
Get your price
You see your price in the chat. A set price is paid at checkout; any other job is quoted first.
Choose your visit
Give your address and when you are free, and the visit is arranged.
Follow your job from booking to receipt
See when we're on our way, get your job report the moment we finish, and pay in seconds.
Track us on our way
See us on the map with a live arrival time.
Your job report, same day
See exactly what was done as soon as we finish.
Invoice and receipt in one place
Pay online in seconds, and your receipt is always there when you need it.
Why choose Lighting Electrical
- Reviews
- 61
- Rating
- 4.7
- Trading since
- 2016
“Ten years on Colchester housing stock and I have seen most of it: terraces where the lighting circuit has been extended once too often, boards fitted before RCDs were standard, new builds with sockets nowhere near the kitchen. I check the earthing, the bonding and whether the supply will carry another load before I price anything, because the age of a house settles nothing on its own.”
Valandi Kotorri, Lighting Electrical
Book NowWhy do my LED lights flicker on a Varilight dimmer?
The lowest brightness setting is usually below what the lamps can hold. Many Varilight LED dimmers let us raise that level so the lamps stop flickering at the bottom of the range. Lamps that are not marked dimmable flicker on any dimmer.
Will a Varilight dimmer work with my LED bulbs?
It will if the bulbs are marked dimmable and the total load sits inside the dimmer's rated range. We add up the wattage of every lamp on the switch before choosing the module. One or two low wattage lamps can fall below a dimmer's minimum load.
Can I have a dimmer on a landing with two switches?
Yes. Varilight pairs one master dimmer with a secondary unit at the other switch. Both points then dim the same lights.
Can you match my existing Varilight plates?
Usually, yes, because Varilight makes its switches, dimmers and sockets in many plate finishes. We fit the same finish where it is still made. Where it is not, you see the nearest current plate before anything comes off the wall.
Why do my lights glow faintly when the dimmer is off?
Some dimmers pass a tiny current through the lamps to power their own electronics when there is no neutral at the switch. LED lamps can glow on that current. The usual cure is a dimmer wired with a neutral or a small load correction device beside the lamps.



