What to do in an electrical fire at home

Switch off at the fuse board if you can reach it safely, then leave the room. Lighting Electrical in Peterborough isolates the burnt circuit and names the failed part.

Calls answered 24/7

  • 10 years trading

Why does an electrical fire start at home?

An electrical fire starts when a loose joint, an overloaded cable or a failed appliance heats until the fitting or insulation burns.

  • A loose joint that arcsA loose screw at a socket, switch or light lets the conductors spark. That spark is arcing, and the heat chars the plastic until it smokes.
  • Too much load on one cableA breaker is the switch in the fuse board that guards one circuit. Heaters and extension leads piled on one socket circuit warm the cable until the insulation softens and smokes.
  • A board with no RCDAn RCD is a safety switch that opens when current leaks away from the circuit. A fuse board fitted before RCDs were standard waits for a fuse to melt, so a leaking joint keeps heating.
  • A crushed flex or coiled leadA flex trapped under a rug or a coiled extension cannot shed heat. The insulation melts, the conductors touch, and the short sets the plastic alight.
  • Water across a live fittingWater on a socket, a light or an outside fitting bridges the contacts. Current then leaks to earth, the safety path back to the board, and the joint heats if the protective device stays closed.

What can you check safely in an electrical fire?

You can get people out, look from a distance, and use a normal switch only when it is cool. Covers, flexes and fuse board screws stay untouched.

  • Everyone out of the roomLeave the room where you see smoke, sparks or flames. Shut the door on the way out if you can do that without going back. Phone the fire service while you are outside.
  • The main switch if it is safeThe main switch on the fuse board cuts every circuit. Use it only when the board is cool, quiet and free of smoke. If the board is hot or in smoke, leave it alone.
  • Heat, noise or brown marksLook from a distance for brown marks, a buzz, or a burning smell at a socket or a light. That circuit stays off. You do not touch the face, the screws or a melted plug.
  • Which breaker has openedWith the cover still on, a breaker sitting down shows the circuit that opened. Leave it down after smoke or heat. A second reset pushes current back through the burnt joint.

When should you book after an electrical fire?

Book Now when a socket, a light, a cable or the fuse board has smoked, sparked or smelt of burning, even after a breaker has opened.

  • Smoke, sparks or a burning smellThe circuit that smoked stays switched off. Another reset can relight the joint. Book Now so we test the failed part before anyone uses that circuit.
  • A hot socket, switch or boardHeat means the joint is still failing. On a cool board, use the breaker handle to leave that circuit off. Keep your hands off screws, covers and melted plastic.
  • Power returns after scorchingSockets or lights that work again after smoke still hide a charred joint. Leave that fitting unused. The circuit needs a test before it is put back into daily use.

What happens on a visit after an electrical fire?

We isolate the burnt circuit first, test it dead, and name the failed part before any fitting or cable is changed.

  • The burnt circuit comes offWe ask where the smoke or the smell started and which breaker opened. We read the fuse board with the cover on. We switch off that circuit, and we leave sound circuits on.
  • Dead tests name the failed partWe prove the circuit is dead before a cover comes off. Tests on the dead cable show a short, a break or a leak to earth. Those readings separate a socket, a switch, a light, a breaker and a length of cable.
  • The repair after you accept itWe name the failed part before we change anything. A sound fitting stays closed. A repair that changes the circuit is recorded on a minor works certificate with our NAPIT registration.
  • Earthing and bonding before a later priceEarthing is the path that carries fault current so a breaker can open. Bonding joins metal pipes to that earth. We check both, and whether the supply can feed the load, before we price any later work.

What does an electrical fire visit cost?

The time spent isolating and testing the burnt circuit sets the price. That time covers attendance, the dead tests, and naming the failed part. A replacement fitting, a minor works certificate, or a later fuse board replacement changes the price.

From £90 an hour

Included in the call-out

  • Attendance at the property in Peterborough or a nearby Essex town
  • Isolation of the failed circuit, fitting or board
  • Fault finding on the circuit that has gone down
  • Temporary making safe so the rest of the installation can be used where that is possible
  • A written note of what failed and what work should follow

Not included automatically

  • A full house rewire or a planned consumer unit replacement on the same visit unless already quoted
  • Parts we do not carry in the van, which we price in writing before we fit them
  • Work on another trade such as gas, plumbing or structural fabric

Ways to pay

  • Visa
  • Mastercard
  • American Express
  • Apple Pay
  • Google Pay
  • Klarna
  • Pay by bank
  • Bank transfer
  • A scorched socket takes less time to trace than burnt cable buried in a wall.
  • We fit a socket, switch, breaker or cable only after the tests show that part has failed.
  • Fuse board replacement is written up separately when the board itself has failed.

View the emergency call-out cost guide

How booking works

  1. Tell us about the job

    Tap Book Now and describe the work in the chat. Photos help.

  2. Get your price

    You see your price in the chat. A set price is paid at checkout; any other job is quoted first.

  3. Choose your visit

    Give your address and when you are free, and the visit is arranged.

Why choose Lighting Electrical

We work with Hager, Wylex, Contactum, BG Electrical, MK Electric, Varilight, myenergi, Ohme, Hypervolt, Andersen, Aico, FireAngel and Mira.

Photo of Valandi KotorriValandi KotorriElectrician
Reviews
61
Rating
4.7
Trading since
2016
“Ten years on Colchester housing stock and I have seen most of it: terraces where the lighting circuit has been extended once too often, boards fitted before RCDs were standard, new builds with sockets nowhere near the kitchen. I check the earthing, the bonding and whether the supply will carry another load before I price anything, because the age of a house settles nothing on its own.”

Valandi Kotorri, Lighting Electrical

Book Now

Questions about an electrical fire at home

Still have a question?

Should I put water on an electrical fire?

No. Water carries current from a live circuit to a person who touches it. Use the main switch only when the fuse board is cool, quiet and free of smoke, then leave the room. We test the circuit before it is used again.

Can I reset the breaker after the smoke stops?

No. Switching it back on sends current through the burnt joint. Leave the breaker off and leave the fitting unused. We name the failed part from the tests before that circuit is switched on.

Will you replace the fuse board on the same visit?

Only when the tests show the board has burnt and you accept a separate written price for fuse board replacement. A burnt socket or switch is repaired on its own. A board that tests sound stays in place.

What paperwork follows an electrical fire repair?

A minor works certificate records the tests when the repair changes the circuit, and it carries our NAPIT registration. If we isolate the circuit and change nothing, we write down the readings and the failed part. An Electrical Installation Condition Report, an EICR, is a separate inspection of the whole installation.

Related problems

Sources

Updated 16 November 2026

Book or ask a question

Calls answered 24/7

Areas we cover (1)