EV charger red light

An EV charger red light means charging has stopped because the unit detected a fault. Lighting Electrical tests the dedicated supply in Peterborough and names the failed part.

Calls answered 24/7

  • 10 years trading

Why is my EV charger showing an error light?

The charger shows an error light because it has detected a fault and stopped the charge. The fault is in the supply, the dedicated circuit, the lead or the charger.

  • The charger switch has openedThe charger has its own breaker or RCBO in the fuse board. An RCBO is a single switch that opens on too much current and on current leaking to earth. Damp in the plug or a cut lead opens that switch, and the charger shows a fault light.
  • The earth path has been lostThe charger measures the earth path that keeps the car body from becoming live. When that path is lost the charger stops and shows a fault light. We check bonding, the joint from metal pipes back to the fuse board, before we price any further work.
  • The lead signal has failedThe lead carries a small control signal between the car and the charger. A bent pin, a cut tethered lead or a plug sitting loose in the weatherproof socket breaks that signal. The charger stays powered and shows a fault light instead of charging.
  • Heat or a wrong supply voltageStrong sun on the case, or a supply voltage outside the range the charger allows, makes it stop to protect its contacts. The fault light stays on while the circuit can still be live. Charging waits until the case has cooled or the supply is back in range.
  • The load sensor has fallen offmyenergi, Ohme, Hypervolt and Andersen chargers can pause so the house is not overloaded. A sensor clipped round the thick cables at the electricity meter reads that load. If the sensor falls off, the charger shows a fault light and will not start.

What can I check on an EV charger safely?

You can check the fault light, the app, the lead and the closed fuse board without opening the charger. Every screw stays in, and you keep your hands off the wiring.

  • The fault light and the appRead the fault light, then open the app for a myenergi, Ohme, Hypervolt or Andersen charger. Write down the message on the screen. A schedule that is paused is not the same as a fault, and the charger cover stays shut.
  • The car unplugged and the lead seatedStop the session in the app and unplug the car. Push the tethered plug, or the plug in the weatherproof socket, fully home and start once more. If the same fault light returns, leave the car unplugged.
  • The charger switch with the cover shutRead the switch marked for the charger through the closed fuse board cover. Lift it once only when the board feels cool, stays silent and has no burning smell. If it falls again, leave it down.
  • Heat, damage or water on the outsideLook at the plug pins, the lead sheath and the socket hood. Melted plastic, a cracked case or water in the hood means you stop using the charger. Leave the charger switch down and do not push anything into the socket.

When should I book for an EV charger error light?

Book Now when one reset leaves the fault light on, or when the lead or the fuse board is hot, wet or smelling of burning.

  • The fault light comes backYou seated the lead again and lifted the charger switch once. The fault light returns or the switch opens at once. Leave the switch down, because another reset heats the terminals.
  • Heat, a buzz or a damaged leadA warm plug, a buzz or brown marks on the pins means a loose contact is sparking. That spark is arcing. Arcing chars the plastic around the pin, so turn the circuit off with the charger switch on the fuse board.
  • Other circuits go off with the chargerAn RCD is a safety switch that opens when current leaks to earth. If the charger trips an RCD that also feeds sockets or lights, those circuits go off as well. Leave every switch that opened in the down position.
  • The car charges somewhere elseThe same car charges on a different charge point while this fault light stays on. The fault then sits with this supply, this lead or this charger. The circuit needs a dead test rather than another reset.

What happens on a visit for an EV charger error light?

We inspect the charger and test its dedicated circuit, then tell you the failed part before we change anything. The repair starts only after you accept the named repair.

  • The light, the app and the chargerWe ask when the fault light came on and whether the car was connected. We read the app message with you. We look at the myenergi, Ohme, Hypervolt or Andersen charger and the fuse board while the cover is still on.
  • Measurements with the power offWe switch the charger circuit off and confirm it is dead before any measurement. One test shows a broken conductor. The next shows live metal touching earth, or insulation that is leaking.
  • Earth path and room on the supplyWe test the earth path and the bonding that joins metal pipes to the fuse board. We test whether the supply can feed the charger together with the rest of the house. You hear which part failed before we price any parts.
  • The repair or a replacement chargerWe fit a failed breaker, cable or lead after you accept that repair. When the charger itself has failed, we price EV charger installation on its own. We issue a minor works certificate for any circuit we alter, showing the tests and our NAPIT registration.

What does an EV charger fault visit cost?

We charge Electrical Fault Finding & Repair by the time spent on the charger circuit. That time includes the dead tests, a spoken diagnosis, and the start of the repair after you accept the work. A new breaker, a length of cable, a tethered lead or a minor works certificate changes the price. Replacing the charge point is priced as EV charger installation, as a separate job.

From £75 an hour

Included when agreed

  • Testing at the board and along the failed circuit until the cause is named
  • A spoken diagnosis before any part is swapped
  • Repair of the failed joint, accessory, cable or protective device once you accept the hourly work
  • Making the circuit safe if it cannot be left live that day
  • A minor works certificate when the repair needs one

Not included automatically

  • A full house rewire or a new consumer unit as the first step
  • Solar, battery, EV charger or forklift charger work
  • Guesswork replacement of parts that have not failed

Ways to pay

  • Visa
  • Mastercard
  • American Express
  • Apple Pay
  • Google Pay
  • Klarna
  • Pay by bank
  • Bank transfer
  • Testing a pedestal charge point and the cable back to the fuse board takes longer than checking a loose tethered lead.
  • A myenergi, Ohme, Hypervolt or Andersen part is added only when the test shows that part has failed.
  • We price emergency electrician attendance separately from Electrical Fault Finding & Repair.

View the fault finding cost guide

How booking works

  1. Tell us about the job

    Tap Book Now and describe the work in the chat. Photos help.

  2. Get your price

    You see your price in the chat. A set price is paid at checkout; any other job is quoted first.

  3. Choose your visit

    Give your address and when you are free, and the visit is arranged.

Why choose Lighting Electrical

We work with Hager, Wylex, Contactum, BG Electrical, MK Electric, Varilight, myenergi, Ohme, Hypervolt, Andersen, Aico, FireAngel and Mira.

Photo of Valandi KotorriValandi KotorriElectrician
Reviews
61
Rating
4.7
Trading since
2016
“Ten years on Colchester housing stock and I have seen most of it: terraces where the lighting circuit has been extended once too often, boards fitted before RCDs were standard, new builds with sockets nowhere near the kitchen. I check the earthing, the bonding and whether the supply will carry another load before I price anything, because the age of a house settles nothing on its own.”

Valandi Kotorri, Lighting Electrical

Book Now

Questions about an EV charger error light

Still have a question?

Is a red light on my EV charger a fault?

Yes. The charger has stopped the charge because it detected a problem on the supply, the lead or the charger itself. We run dead tests on the dedicated circuit and tell you which of those failed. A paused schedule in the app is the case that is not a fault.

Should I reset the charger breaker again?

Lift the charger switch once, and only when the fuse board feels cool, stays silent and has no burning smell. If the switch falls again or the fault light returns, leave it down. Further resets heat the terminals.

Will you fit a new charger before you test?

No. We name the failed breaker, cable, lead, sensor or charger first. We fit that part only after you accept the repair, and a charger that tests sound stays in place. EV charger installation is priced separately when the unit itself has failed.

What paperwork do I get after the visit?

When the repair alters the circuit, we issue a minor works certificate showing the test results and our NAPIT registration. When we change nothing, we still leave you the readings and the name of the failed part. An Electrical Installation Condition Report, an EICR, is a separate inspection of the whole installation.

Related problems

Sources

Updated 16 November 2026

Book or ask a question

Calls answered 24/7

Areas we cover (2)