Flooded electrics after a leak or flood

Flooded electrics stay isolated until Lighting Electrical tests the wet circuits in Peterborough and switches back only the ones that pass.

Calls answered 24/7

  • 10 years trading

Why do electrics fail after a leak or flood?

Water across live contacts sends current down the earth path and the protective device opens. The failed part is the wet fitting, the cable in the fabric, or the fuse board.

  • Water inside a socket or a switchWater joins the live contact to the earth contact inside the faceplate. The RCD, the switch that opens when current leaves the circuit, drops that circuit. It stays off until the fitting is dry and tested.
  • A fuse board standing in waterFloodwater in a cupboard reaches the breakers and the main switch. Those devices can pass current through the water. We treat that board as unsafe to reset until it is isolated and tested.
  • Cable soaked under a floor or in a wallFloodwater sits against cable under floors and behind plaster. Damp insulation lets current pass between the wires. The breaker on that run opens, and it drops again if someone resets it.
  • Rain in an outside light or socketA wall lantern, an outside socket or a sealed enclosure fills with rain. Water on the terminals trips the circuit that feeds the fitting. Circuits on a different device indoors can stay on.
  • An appliance left standing in waterA fridge, a washing machine or a heater leaks through its flex or its motor when it stands in water. The circuit breaker opens. The appliance stays unplugged once it can be reached without touching the water.

What can you check safely after a flood?

You can look from a dry place, pull dry plugs and use the breaker handles on a dry fuse board. Every cover stays on. You do not open an appliance.

  • Where the water reachedLook at sockets, switches, lights and the fuse board from a dry standing place. If water is on them or pooled under them, leave them untouched. Tell us which fittings got wet when you Book Now.
  • Breakers on a dry fuse boardIf the board is dry, cool and quiet, read the labels through the closed cover. A breaker sitting down is the circuit that opened. One reset is reasonable. If it opens again, leave it down.
  • Plugs you can pull while staying dryPull the plugs on portable appliances that are dry and clear of the water. Leave any appliance standing in water as it is. Keep your hands off a wet flex and leave the appliance cover shut.
  • A lamp in a dry roomPlug a lamp you already know works into a dry socket in another room. Note which rooms still have lights and which are dark. That pattern shows which circuits opened.

When should you book for flooded electrics?

Book Now when water has reached a socket, a light or the fuse board, or when a breaker will not stay on after the area looks dry.

  • Water reached a socket, light or the boardAny fitting or fuse board that got wet stays unused, even after the puddle has gone. Book Now so the circuit can be isolated and tested before anyone switches it on.
  • The breaker will not stay onThe appliances you could reach are unplugged and the breaker still opens. Current is still leaving the circuit. Another reset heats the breaker and the cable, so leave it off.
  • A burning smell, a buzz or warmthA burning smell, a buzz or a warm faceplate means a joint is failing as well as the damp. Use a dry breaker handle to switch that circuit off if you can do so without touching water. Then Book Now.

What happens on a visit for flooded electrics?

We isolate every wet circuit first, test it while it is off, and name the failed part before anything is changed.

  • Which rooms and fittings got wetWe ask which rooms took water and which breakers are down. We look at the fuse board and the wet fittings with you. We switch off every circuit that is wet or will not hold, and we leave sound circuits on.
  • Tests on the isolated circuitsWith those circuits off, we measure whether the cable is shorted, broken or leaking. The readings separate a wet socket, soaked cable, a failed breaker and an appliance that stood in the water.
  • Earthing, bonding and the supplyEarthing is the path that carries fault current so a breaker can open. Bonding is the link between metal pipes and the fuse board. We check both, and whether the supply can carry the load, before we price further work.
  • What is switched on and what is quotedWe switch on only the circuits that test sound. A socket, breaker or short cable repair starts after you accept it. A change to a circuit is recorded on a minor works certificate with our NAPIT registration. A soaked fuse board is quoted as its own replacement.

What does a flooded electrics visit cost?

The price covers attendance, isolation of every wet circuit and the tests that name the failed part. A longer test along soaked cable, a replacement part, or a minor works certificate changes the price. Fuse board replacement is a separate job when the board itself has failed.

From £90 an hour

Included in the call-out

  • Attendance at the property in Peterborough or a nearby Essex town
  • Isolation of the failed circuit, fitting or board
  • Fault finding on the circuit that has gone down
  • Temporary making safe so the rest of the installation can be used where that is possible
  • A written note of what failed and what work should follow

Not included automatically

  • A full house rewire or a planned consumer unit replacement on the same visit unless already quoted
  • Parts we do not carry in the van, which we price in writing before we fit them
  • Work on another trade such as gas, plumbing or structural fabric

Ways to pay

  • Visa
  • Mastercard
  • American Express
  • Apple Pay
  • Google Pay
  • Klarna
  • Pay by bank
  • Bank transfer
  • One wet socket takes less test time than a soaked cable under a floor.
  • A socket, breaker or cable is fitted only when the tests show it has failed.
  • Fuse board replacement and an EICR are each priced on their own when either is needed.

View the emergency call-out cost guide

How booking works

  1. Tell us about the job

    Tap Book Now and describe the work in the chat. Photos help.

  2. Get your price

    You see your price in the chat. A set price is paid at checkout; any other job is quoted first.

  3. Choose your visit

    Give your address and when you are free, and the visit is arranged.

Why choose Lighting Electrical

We work with Hager, Wylex, Contactum, BG Electrical, MK Electric, Varilight, myenergi, Ohme, Hypervolt, Andersen, Aico, FireAngel and Mira.

Photo of Valandi KotorriValandi KotorriElectrician
Reviews
61
Rating
4.7
Trading since
2016
“Ten years on Colchester housing stock and I have seen most of it: terraces where the lighting circuit has been extended once too often, boards fitted before RCDs were standard, new builds with sockets nowhere near the kitchen. I check the earthing, the bonding and whether the supply will carry another load before I price anything, because the age of a house settles nothing on its own.”

Valandi Kotorri, Lighting Electrical

Book Now

Questions about electrics after a flood

Still have a question?

Can I switch the power on after the water has gone?

No. Water can sit inside a socket or a cable after the floor looks dry. We test each wet circuit and switch on only the ones that pass.

Will you change the fuse board on the same visit?

Only if the tests show the board has failed and you accept a separate price for fuse board replacement. A sound board stays in place. Wet circuits remain off until they pass.

What paperwork do I get after the repair?

A minor works certificate follows when we change a circuit, and it shows the test results with our NAPIT registration. If we only isolate the wet circuits, we leave you the readings and the name of the failed part. An EICR inspects the whole installation and is booked on its own.

Should I unplug a washing machine standing in water?

No. Leave it plugged in if reaching the plug means standing in water or holding a wet flex. Switch that circuit off at a dry breaker if you can do that safely. We test the circuit with the appliance isolated.

Can the rooms that stayed dry keep their power?

Yes. We switch off the wet circuits and leave each sound circuit on. A breaker that covers both a wet room and a dry room stays off until the wet part is separated or repaired. We tell you which rooms that affects before we isolate them.

Related problems

Sources

Updated 16 November 2026

Book or ask a question

Calls answered 24/7

Areas we cover (1)