Fuse keeps blowing
A fuse keeps blowing when too much current flows through a plug or a circuit fuse. Lighting Electrical in Peterborough tests that fuse and names the failed appliance, socket or cable.
Calls answered 24/7
- 10 years trading
Why does a fuse keep blowing?
A fuse melts to stop a cable or an appliance overheating. It keeps blowing when the same overload or the same short is still there after a fuse of the right rating is fitted.
- A short inside the appliance or flexA short joins the live and neutral conductors. Current rises at once and the fuse melts. The same short blows the next fuse of the same rating. The appliance stays unplugged until we test it.
- A fuse rated below the appliance loadA 3 amp fuse suits a small appliance. A kettle or a heater needs a 13 amp fuse in a BS 1362 plug. A fuse that is too small melts during normal use. A larger fuse than the flex allows lets the flex overheat.
- Too many appliances on one adaptorEach plug fuse protects its own flex. An adaptor stacks several loads onto one wall socket. The socket contacts and the adaptor overheat. A fuse then melts, or the plug body goes warm, even when each appliance is sound alone.
- A loose connection in the plugA loose live or neutral screw heats the fuse and the pin. Heat weakens the fuse so it melts below its rating. Brown marks on the plug or a smell of hot plastic show that heating. The socket face can scorch in the same way.
- Fuse wire of the wrong sizeOlder fuse boards use fuse wire rather than a cartridge or a breaker. Wire that is too thin melts on a normal load. Wire that is too thick stays intact when it should melt. We match the wire to the circuit only after a test shows the circuit is sound.
What can I check safely when a fuse keeps blowing?
You can read the fuse, unplug appliances and look at the plug and the closed fuse board. You leave the appliance case shut and you leave every cable untouched.
- The rating marked on the plug fuseRead the number on the fuse in the plug, or on a fuse you have already taken out. A small lamp or a charger uses a 3 amp fuse. A kettle, toaster or heater uses a 13 amp fuse. You do not open the appliance to find that number.
- Other plugs in the same socketPull every plug from the adaptor or the double socket. Fit one fuse of the rating the appliance maker states. If that fuse melts as soon as you switch on, leave the appliance unplugged.
- Heat, marks or a burning smellA warm plug, brown pin holes or a smell of hot plastic means a connection is heating. Switch the appliance off and unplug it if the plug is cool enough to hold. Leave a hot fuse board cover shut.
- One appliance or the whole roomIf only one appliance stops, the fuse in its plug has melted. If several sockets or the lights go together, a fuse in the fuse board has melted. Note which fuse opened before you touch a switch.
When should I book for a fuse that keeps blowing?
Book Now when a fuse of the right rating melts again, or when a plug or the fuse board is hot or smells of burning. A single spent fuse in a cool lamp plug is one you can replace once.
- The right fuse melts againYou fitted the rating given for that appliance and it melted on the next use. The fault is in the appliance, the flex, the socket or the circuit. Another fuse will melt the same way and can heat the plug.
- The plug or the board smells of burningHeat, a buzz or a burning smell means metal is arcing. Arcing is a spark jumping across a loose joint. Unplug if the plug is safe to hold. Leave the fuse board cover on and use only the switch on the front.
- Several points die togetherA melted fuse in the fuse board cuts every light or socket on that circuit. Putting new wire in before a test can leave a short on the cable. Book Now and leave that fuse out.
What happens on a visit for a blowing fuse?
We test the melted fuse and the appliance that was running, then we name the failed part before a plug, a socket or a cable is changed.
- Which fuse melted and whenWe ask which appliance was on, which plug fuse or board fuse melted, and whether a larger fuse was tried. We look at the plug, the socket and the fuse board with you. The cover stays on until a tester shows the circuit is dead.
- Tests on the flex, socket and cableWe isolate the circuit at the fuse board. A dead test checks the flex and the cable for a short or a break. We measure whether current is leaking to earth. Earth is the safety path that carries a fault away from you. The readings separate a failed appliance from a failed socket or cable.
- The failed part, then the repairWe name the failed flex, socket, joint or appliance and wait for you to accept the repair before we fit anything. A sound appliance stays unplugged when the fault is inside it. A sound socket stays on the wall.
- A second test and the certificateWe test the circuit after the repair. Where the circuit was altered we issue a minor works certificate, and the certificate carries our NAPIT registration. Before a further price we check the earthing, the bonding and whether the supply can carry the load. Bonding links metal pipes to the earthing.
What does a blowing fuse visit cost?
Electrical Fault Finding & Repair is charged by the hour. The price covers tests on the blowing fuse, the diagnosis we give you, and the repair after you accept it. Tracing one warm plug takes less time than testing a circuit whose fuse melts only when several appliances run. A replacement plug, socket or length of cable changes the price, as does a minor works certificate when the repair needs one.
From £75 an hour
Included when agreed
- Testing at the board and along the failed circuit until the cause is named
- A spoken diagnosis before any part is swapped
- Repair of the failed joint, accessory, cable or protective device once you accept the hourly work
- Making the circuit safe if it cannot be left live that day
- A minor works certificate when the repair needs one
Not included automatically
- A full house rewire or a new consumer unit as the first step
- Solar, battery, EV charger or forklift charger work
- Guesswork replacement of parts that have not failed
Ways to pay


- Pay by bank
- Bank transfer
- The hour covers the tests, the spoken diagnosis and the repair of the part that failed, after you accept it.
- A plug, a socket, a fuse carrier or a length of cable is added only when the tests show that part has failed.
- A minor works certificate is added when the repair changes the circuit, and it carries our NAPIT registration.
How booking works
Tell us about the job
Tap Book Now and describe the work in the chat. Photos help.
Get your price
You see your price in the chat. A set price is paid at checkout; any other job is quoted first.
Choose your visit
Give your address and when you are free, and the visit is arranged.
Why choose Lighting Electrical
We work with Hager, Wylex, Contactum, BG Electrical, MK Electric, Varilight, myenergi, Ohme, Hypervolt, Andersen, Aico, FireAngel and Mira.
- Reviews
- 61
- Rating
- 4.7
- Trading since
- 2016
“Ten years on Colchester housing stock and I have seen most of it: terraces where the lighting circuit has been extended once too often, boards fitted before RCDs were standard, new builds with sockets nowhere near the kitchen. I check the earthing, the bonding and whether the supply will carry another load before I price anything, because the age of a house settles nothing on its own.”
Valandi Kotorri, Lighting Electrical
Book NowCan I stop the blowing by fitting a bigger fuse?
No. A bigger fuse lets more current through the flex than the flex is made for. The flex can overheat while the fuse stays intact. Fit only the rating the appliance needs, and book a test if that fuse melts again.
Is a blowing fuse the same as a tripping breaker?
No. A fuse melts and has to be replaced. A breaker is a switch you can reset. Both open because of too much current or a fault to earth. We test the circuit that opened and we do not swap a fuse for a breaker during that test.
Will you replace the fuse before you find the fault?
No. We test the appliance, the plug and the circuit first and name the failed part. A new fuse goes in when that part is sound, or after the repair you have accepted. A fuse that melted from a short stays out while the short remains.
What if the fuse is in the fuse board, not the plug?
We treat a melted board fuse as a fault on that circuit. We isolate the circuit and test the cable, the sockets and the fittings on it. A cartridge or a length of fuse wire goes back only after those tests show the circuit can take it.
Do I get paperwork after the repair?
You get a minor works certificate when the repair changes the circuit. It records the tests for the work we finished and our NAPIT registration. If the fault is inside an appliance and we change no wiring, we tell you the finding and leave that appliance unplugged.
Related problems
- Automatic gate not openingA gate that will not move has lost its supply, its safety beam or its motor control, so the outdoor circuit needs a test.
- Buzzing sound in the wallA buzz inside a wall is a loose joint, a dimmer or a damaged cable on that circuit.
- Circuit breaker keeps trippingThe breaker keeps tripping because a fault is still on the circuit, in an appliance, a cable, a joint or the protective device.
- Consumer unit tripping with nothing plugged inThe consumer unit trips with nothing plugged in because fixed wiring or the safety switch is sending current to earth.
- Downstairs circuit keeps trippingThe downstairs breaker or RCD opens because a socket, light, cable or appliance on that floor is leaking or overloaded.
- Driveway lights not workingDriveway lights go dark when the outdoor circuit, a sensor or a lantern fails, while rooms on another breaker stay lit.
Sources
- Electrical Safety First: Plugs and fuses (BS 1362 fuse ratings)
- Electrical Safety First: Ratings of electrical appliances
- Electrical Safety First: Overloading sockets
- BS 7671: IET Wiring Regulations (18th Edition)
Updated 16 November 2026
