Lights pulsing on and off

Lights that pulse on and off are losing a steady feed on the lighting circuit. Lighting Electrical in Peterborough finds the loose joint, dimmer or driver and tells you the failed part.

Calls answered 24/7

  • 10 years trading

Why do lights pulse on and off?

Lights pulse when the lighting circuit keeps connecting and disconnecting, or when its voltage swings. One room means a fitting or a switch. The whole house means the fuse board or the neutral.

  • A loose terminal in the switch or roseA ceiling rose is the joint above a pendant. A loose screw there lets the feed touch and part, so the lamp goes bright, then dark, then bright. The same loose screw in a light switch does this to every lamp on that switch.
  • A dimmer that does not suit the lampsA dimmer is a switch that reduces brightness by chopping the supply. Varilight and MK Electric dimmers need lamps made for that chop. LED lamps, the low energy bulbs in most fittings, pulse in a steady beat on the wrong dimmer. Full brightness steadies them when the mismatch is the cause.
  • A lamp driver that keeps restartingA driver is the small unit inside an LED fitting that feeds the lamp. When it overheats it shuts off, cools, and starts again, so the light pulses on a regular gap. One downlight doing this, with the others steady, points at that driver.
  • A loose neutral on the lighting circuitThe neutral is the wire that carries current back to the fuse board. A loose neutral lets the voltage swing, so lamps flare and fade together. The swing can show in more than one room. It is a failed joint, not a tired lamp.
  • Too many joints on the lighting runEach extra light or moved point adds a joint in the cable. A poor joint heats, opens, cools and closes, and the lamps on that run pulse. Lamps on another breaker, the fuse board switch for a different circuit, stay steady.
  • A movement sensor switching the lanternA PIR sensor watches for body heat and switches a lantern. PIR means passive infrared. A sensor aimed at a road, a tree or a reflective window turns the lamp on and off in a pulse. We fit wall lanterns with these sensors, and the cable can be sound while the sensor keeps triggering.

What can you check safely before a fitting is opened?

You can see which lamps pulse, change a bulb by hand, and read the fuse board through its closed cover. Every screw stays in place.

  • Which lamps pulse togetherStand in each room and watch. One pendant points at that fitting. Every lamp on one switch points at the switch or the dimmer. Every lamp in the house points at the fuse board or the neutral. Note the rooms.
  • A bulb you can change by handWhere the bulb unscrews or lifts out without a tool, fit a bulb that already lights another room. Use the same type. If the pulse stops, the first bulb has failed. If the pulse carries on, the fault is in the wiring, the switch or the driver.
  • The dimmer turned fully upSet the dimmer to its brightest stop for a minute, then switch it off. A pulse that settles at full brightness and returns on a low setting points at the dimmer and the lamps together. Leave the dimmer at full until the visit.
  • Whether a heavy appliance starts itWatch the lights while the kettle, the oven or the electric shower switches on. A dip only at that moment is the supply sagging under load. A pulse that continues after the appliance stops is a joint on the lighting circuit.
  • The lights switch with the cover shutLeave the fuse board cover on. Find the switch marked for lights. A warm front, a buzz or a burning smell means stop using that circuit and use the handle only to switch it off. A cool quiet board stays in use.

When should you book for pulsing lights?

Book Now when the pulse continues after a bulb change, when lamps flare across more than one room, or when a switch, a fitting or the fuse board is hot, buzzing or smelling of burning.

  • The pulse remains after a bulb changeA working bulb still pulses, so the fault is a joint, a dimmer, a driver or the neutral. Another bulb from the cupboard will not clear it. Book Now and leave that switch at one steady setting.
  • Heat, a buzz or a burning smellHeat and a burnt smell mean a joint is arcing. Arcing is a spark jumping across a loose connection. Switch that lighting circuit off with the fuse board handle. Leave the cover screws and the fitting screws untouched.
  • Several rooms pulse at the same timeRooms flaring together mean the neutral or the connection at the fuse board is moving. That swing puts stress on other circuits. Book Now and avoid cycling large appliances while you wait.
  • The lighting switch will not stay upThe lighting switch drops while the lamps are pulsing. One reset is enough when the board is cool and quiet. If it opens again, leave it off. Repeated resets heat the terminals.

What happens on a visit for pulsing lights?

We start with the lamps that pulse, test the lighting circuit while it is switched off, and name the failed part before anything is replaced.

  • Which lamps pulse and when it beganWe ask which rooms pulse, whether a dimmer is in use, and whether it began after a new lamp, a new lantern or a heavy appliance. We look at the fuse board with the cover still on and note the lights switch.
  • Measurements with the circuit offWe switch off the lighting breaker, the fuse board switch for that circuit, and prove the cable is dead. We measure whether the copper still joins end to end and whether current can leak between the wires. The readings separate a switch, a rose, a driver and a neutral joint.
  • The failed part named before we fit anythingWe open only the switch, rose or dimmer those readings indicate. We tell you the failed part in plain words, and a sound fitting stays closed. Earthing is the safety path for fault current. Bonding links metal pipes to that path. We check both, and whether the supply can take more load, before we price any further work.
  • Repair of the lighting circuitThe repair of that joint, switch, dimmer or driver goes ahead after you say yes to it. We test the circuit again once it is back together. A minor works certificate follows when that repair alters the circuit, and it shows our NAPIT registration. If the circuit is unsafe to put back on, we leave the lights switch off.

What does a pulsing lights visit cost?

Electrical Fault Finding & Repair is charged by the hour. That price pays for the measurements on the pulsing circuit, an explanation of the cause, and the first repair steps after you say yes. A single warm dimmer takes less time than a neutral joint across several rooms. A replacement part, a minor works certificate, or a fuse board change moves the price. Emergency electrician attendance is charged as its own job.

From £75 an hour

Included when agreed

  • Testing at the board and along the failed circuit until the cause is named
  • A spoken diagnosis before any part is swapped
  • Repair of the failed joint, accessory, cable or protective device once you accept the hourly work
  • Making the circuit safe if it cannot be left live that day
  • A minor works certificate when the repair needs one

Not included automatically

  • A full house rewire or a new consumer unit as the first step
  • Solar, battery, EV charger or forklift charger work
  • Guesswork replacement of parts that have not failed

Ways to pay

  • Visa
  • Mastercard
  • American Express
  • Apple Pay
  • Google Pay
  • Klarna
  • Pay by bank
  • Bank transfer
  • The hour pays for tracing the pulse and starting that repair, not for a new lighting scheme.
  • A Varilight or MK Electric dimmer, or a breaker from Hager, Wylex, Contactum or BG Electrical, is fitted only after the tests show it has failed.
  • When the pulse comes from the lighting breaker, a fuse board change is priced as another job.

View the fault finding cost guide

How booking works

  1. Tell us about the job

    Tap Book Now and describe the work in the chat. Photos help.

  2. Get your price

    You see your price in the chat. A set price is paid at checkout; any other job is quoted first.

  3. Choose your visit

    Give your address and when you are free, and the visit is arranged.

Why choose Lighting Electrical

We work with Hager, Wylex, Contactum, BG Electrical, MK Electric, Varilight, myenergi, Ohme, Hypervolt, Andersen, Aico, FireAngel and Mira.

Photo of Valandi KotorriValandi KotorriElectrician
Reviews
61
Rating
4.7
Trading since
2016
“Ten years on Colchester housing stock and I have seen most of it: terraces where the lighting circuit has been extended once too often, boards fitted before RCDs were standard, new builds with sockets nowhere near the kitchen. I check the earthing, the bonding and whether the supply will carry another load before I price anything, because the age of a house settles nothing on its own.”

Valandi Kotorri, Lighting Electrical

Book Now

Questions about lights pulsing on and off

Still have a question?

Will changing the bulbs stop the pulsing?

A bulb change stops the pulse only when that bulb is the failed part. If a bulb that works in another room still pulses here, the fault sits in the switch, the dimmer, the driver or a joint. We name that part before we fit anything.

Should I leave the pulsing lights switched on?

Leave them on only while the fittings, the dimmer and the fuse board stay cool, quiet and free of any burning smell. Heat, a buzz or a smell means switch that lighting circuit off at the breaker handle. The cover stays shut.

Do you fit a new dimmer before you test?

No. We test the lighting circuit first and name the failed dimmer, joint or driver. A Varilight or MK Electric dimmer goes in only when that test shows the dimmer is the fault, and only after you say yes to the repair.

Will a new fuse board stop the pulsing?

A new fuse board stops the pulse only when the tests show the board connection or the lighting breaker is the fault. A loose rose or a failing driver still pulses on a new board. A fuse board change is priced on its own after the test.

What paperwork follows the lighting repair?

Where the repair changes the lighting circuit, a minor works certificate records the tests and our NAPIT registration. If we find the fault and change nothing, you still hear the cause and what the readings showed. An EICR is a separate inspection of the whole installation.

Related problems

Sources

Updated 16 November 2026

Book or ask a question

Calls answered 24/7

Areas we cover (2)