Lights suddenly brighter than normal
Lights that turn suddenly brighter than normal are on a circuit whose voltage has risen. Lighting Electrical in Peterborough measures that voltage and switches those circuits off.
Calls answered 24/7
- 10 years trading
Why are lights suddenly brighter than normal?
The lamps are receiving more voltage than they should. That rise comes from a failed neutral, a high incoming voltage, or a dimmer that has stuck fully on.
- A broken neutral in the installationThe neutral is the return path that keeps each circuit near its proper voltage. When that path breaks in the fuse board or in a joint, one circuit rises and another falls. Lamps on the high side glare. Lamps on the low side look dim at the same moment.
- Incoming voltage that is too highThe supply at the fuse board should sit near 230 volts. When that voltage rises, lamps in every room glare together. Appliances may hum at the same time because they share that high voltage.
- A solar or battery inverter exportingA solar inverter turns panel power into mains power, and a battery inverter does the same for stored charge. Export from either unit can lift the voltage on the fuse board. The lights on that board glare while the unit is exporting.
- A dimmer stuck fully onA dimmer is a switch that lowers the voltage reaching a lamp. When the dimmer fails it can pass the full voltage, so that room looks much brighter than the setting you chose. Other rooms stay as they were. The dimmer plate stays on the wall until we test the circuit.
- A lighting circuit on the wrong neutralA lighting circuit that was extended and tied to another circuit's neutral no longer has a stable return. The lamp voltage then drifts, and the bulbs glare or swing between bright and dim. The joint sits in a ceiling rose, a switch box or the fuse board.
What can you check while the covers stay on?
You can compare rooms, listen for a hum and use the main switch. You leave every cover screwed on and you do not touch a cable.
- Whether one room or every room is brightWalk the rooms and note which lamps glare. One room points to that dimmer or that lighting circuit. Every room glaring, or some rooms glaring while others are dim, points to the neutral or the incoming voltage. Note the rooms before you switch anything off.
- The main switch on the fuse boardThe main switch is the large switch that cuts every circuit. If the lights glare and appliances hum, turn that switch off. Leave the cover shut. A single bright room can stay on its own light switch when the rest of the house looks unchanged in brightness.
- Plugs, hum and the smell of hot plasticPull the plugs on the television and the computer if you can reach them without moving the appliance. A buzz from the fuse board or a smell of hot plastic means you stop there. Keep your hands off the screws and the cables.
When should you book for lights that are too bright?
Book Now when the brightness jumps in more than one room, when lamps glare and others dim together, or when you hear a hum or smell burning.
- Brightness in several rooms at onceSeveral rooms glaring at the same time means the voltage has risen on more than one circuit. Leave the main switch off if you have already turned it off. Book Now so we can measure those circuits.
- Some lamps glaring and others dimThat split is the usual sign of a broken neutral. The high side can overheat equipment left plugged in. Switch the main switch off and Book Now. Leave the bright rooms unused.
- A hum, heat or a burning smellA hum from appliances while the lights glare means the voltage is high. Heat or a burning smell at a switch or the fuse board means a joint is failing. Use the switch handle only. Book Now with that circuit left off.
What happens on a visit for lights that are too bright?
We measure the voltage first and switch off every circuit that is too high. Any repair of a neutral, a dimmer or an inverter connection starts after you accept it.
- Which rooms glared and which switch is offWe ask which rooms glared, which went dim, and whether a solar inverter or a battery inverter was running. We look at the fuse board with you. The cover stays on until the main switch or the lighting breaker is off.
- Voltage on the lights and the incoming cablesWe measure the voltage with a tester on the lighting circuit and on the cables entering the fuse board. A reading far above 230 volts confirms why the lamps glare. If the rise is inside the house we move on to the neutral and the inverter. If the rise is already on the incoming cables we leave the main switch off, test the house neutral while it is dead, and record both readings.
- The neutral, the dimmer or the inverterWith the circuit dead we test the neutral joints, the dimmer and any inverter supply. We name a loose neutral, a failed dimmer or a faulty inverter link before a part is changed. Boards we work on include Hager, Wylex, Contactum, BG Electrical and MK Electric.
- The repair, the tests and the certificateWe repair the failed connection once you accept it, then test the circuit again. A change to the circuit gets a minor works certificate under our NAPIT registration. Before any further price we check the earthing, the bonding and whether the supply can carry the load. Earthing is the path that carries fault current away. Bonding links metal pipes to that earth.
What does a visit for lights that are too bright cost?
Emergency electrician time sets the price for this fault. The price covers attendance, voltage tests on the bright circuits, and switching off what is unsafe to leave on. A repair you accept, a part such as a dimmer or a breaker, or a minor works certificate changes the price.
From £90 an hour
Included in the call-out
- Attendance at the property in Peterborough or a nearby Essex town
- Isolation of the failed circuit, fitting or board
- Fault finding on the circuit that has gone down
- Temporary making safe so the rest of the installation can be used where that is possible
- A written note of what failed and what work should follow
Not included automatically
- A full house rewire or a planned consumer unit replacement on the same visit unless already quoted
- Parts we do not carry in the van, which we price in writing before we fit them
- Work on another trade such as gas, plumbing or structural fabric
Ways to pay


- Pay by bank
- Bank transfer
- Following a broken neutral from room to room takes more time than a single dimmer test.
- A dimmer, breaker or inverter part is fitted only after the test names it.
- A new fuse board is quoted on its own once the neutral inside it has failed.
How booking works
Tell us about the job
Tap Book Now and describe the work in the chat. Photos help.
Get your price
You see your price in the chat. A set price is paid at checkout; any other job is quoted first.
Choose your visit
Give your address and when you are free, and the visit is arranged.
Why choose Lighting Electrical
We work with Hager, Wylex, Contactum, BG Electrical, MK Electric, Varilight, myenergi, Ohme, Hypervolt, Andersen, Aico, FireAngel and Mira.
- Reviews
- 61
- Rating
- 4.7
- Trading since
- 2016
“Ten years on Colchester housing stock and I have seen most of it: terraces where the lighting circuit has been extended once too often, boards fitted before RCDs were standard, new builds with sockets nowhere near the kitchen. I check the earthing, the bonding and whether the supply will carry another load before I price anything, because the age of a house settles nothing on its own.”
Valandi Kotorri, Lighting Electrical
Book NowShould I turn the main switch off?
Yes, if lamps glare in several rooms or appliances start to hum. The main switch cuts the installation and the covers stay on. One bright room can stay on its own light switch until we test that dimmer.
Can high voltage damage my television and my fridge?
Yes. A voltage rise overheats power supplies and motors, so unplug what you can reach and switch the main switch off. We measure the voltage before those circuits go back on. Anything that smells hot stays unplugged.
Will you replace the fuse board because the lights are bright?
Only when the tests find the failure in the neutral or in the board. A failed dimmer or an inverter leaves a sound board in place. Any board change is priced on its own after the readings. Boards we fit include Hager, Wylex and Contactum.
What if a solar inverter is making the lights bright?
We measure the house voltage while the inverter runs, then measure it again with the inverter switched off. A rise that ends when the inverter is off points to that unit. We leave the inverter off if the voltage is still high, and we repair an inverter connection only after you accept that repair.
Do I get paperwork after the repair?
A repair that changes wiring gets a minor works certificate. The certificate lists the test results and our NAPIT registration. When we only isolate the circuit, you still get the voltage readings and the name of the failed part in writing.
Related problems
- Brown marks on a socket or plugBrown marks on a socket or plug mean the connection has overheated, so that circuit stays off until it is tested.
- Burning plastic smell from electricsA burning plastic smell means the insulation on a live joint is getting hot, so that circuit stays switched off until it is tested.
- Burning smell from a socketA burning smell from a socket means a connection is overheating and that circuit should stay off until it is tested.
- Burning smell from the fuse boxA burning smell at the fuse box means a connection or device is overheating, so that circuit stays off until it is tested.
- Electric shock from a light switchA shock from a light switch means the switch face is carrying current and that lighting circuit should be isolated.
- Electric shock from the showerA shock from the shower means current is on the water, the case or the taps, so that circuit stays off until it is tested.
Sources
- BS 7671: IET Wiring Regulations (18th Edition)
- HSE: Electrical Safety at Work
- Electrical Safety First: Safety Guidance
Updated 16 November 2026
