Plug gets hot when in use
A plug that gets hot in use has a loose terminal, an overloaded socket or a failing appliance. Lighting Electrical in Peterborough tests that point and names the part that is heating.
Calls answered 24/7
- 10 years trading
Why does a plug get hot in use?
A plug gets hot in use when resistance at the pins, the socket terminals or the appliance turns current into heat. The warm part is the joint that is carrying the load badly.
- A loose terminal behind the socketThe terminal is the screw that clamps the cable inside the socket. A loose screw sparks under load and the heat runs into the plug pins. The plastic around the holes turns brown.
- Too much load on one socketA kettle, a heater and a dryer on one double socket or one extension lead pull more current than that point is made for. The pins warm while those appliances run together. Separating them shows whether the load was the cause.
- A worn plug or a damaged leadBent pins, a cracked plug body or a frayed lead raise resistance where the current passes. The plug warms as soon as the appliance runs. A second appliance in the same socket staying cool points to the first plug.
- A fault inside the applianceA failing element, motor or internal joint draws extra current through the plug. That plug heats in a socket that is otherwise sound. Other plugs stay cool because they are not carrying the same fault.
- Tired contacts in the socketThe metal springs that grip the pins weaken with age and use. A weak grip sparks each time the appliance is running. Brown marks around the pin holes show the socket face has been overheating.
What can I check safely on a hot plug?
You can compare the plug with the socket face, look for scorch marks and read the fuse board with the lid left on. Every screw stays in and the appliance case stays closed.
- The plug after it is switched offSwitch the appliance off at its own switch and pull the plug out. Feel the plug body, then the socket face. A hot plug with a cool face points to the plug or the appliance. A hot face points to the socket.
- Marks on the pins and the faceLook at the pin holes and the pins themselves. Brown or black marks mean the joint has been sparking. Bent or blackened pins mean you stop using that plug and leave the socket unused.
- One appliance on its ownUnplug every other lead on that socket and on any extension. Run the suspect appliance alone. If the plug still heats, the extra appliances were not the full cause.
- The fuse board with the lid onRead the breaker names through the lid. With the hot plug already out, switch that breaker off if the board is cool and silent. If the board is warm, buzzing or smelling of burning, leave every switch as it is.
When should I book for a hot plug?
Book Now when the plug or the socket is hot to the touch, marked, buzzing or smelling of burning. A kettle plug that is only faintly warm after a boil, and that cools once unplugged, is a different case.
- Too hot to holdHeat you cannot hold on the plug or the socket face means the joint is failing. Switch the appliance off at its own switch and pull the plug. Book Now and leave the socket screws in place.
- Brown marks, a buzz or a burning smellSparking at a loose joint leaves brown marks and a sharp smell. Use the breaker handle on the front of the fuse board to switch that circuit off. Book Now before anyone uses that socket again.
- Heat that follows the plug or the socketA plug that warms in a second socket points to the appliance or the plug. A socket that warms with a different plug points to that socket. Book Now so the failed part is named on test.
What happens on a visit for a hot plug?
We isolate the circuit that fed the hot plug, test it, and name the failed part before any socket is changed. Other circuits in the property stay on.
- What was running and what felt hotWe ask which appliance was in use and whether the plug, the socket face or both were hot. We stand at the fuse board with you and note the breaker for that room. No screw comes out until a tester shows the circuit is dead.
- Measurements with the circuit offWe switch that breaker off. Tests on the dead cable and socket separate a loose connection, a burnt socket, a damaged lead and a fault in the appliance. You hear that result before a face comes off the wall.
- Only the failed socket is openedThe face comes off only the socket whose readings failed. We remake that terminal or fit a new socket in its place. Every sound socket stays shut, and the appliance case stays closed.
- The repair and the certificateThe repair of the named part starts after you accept it. We test the circuit again when the work is finished. A certificate for minor works follows a change to a socket, cable or breaker, and NAPIT registration is on that certificate. The breaker stays off if the circuit cannot be switched back on.
What does a hot plug visit cost?
Electrical Fault Finding & Repair is charged for the time on site. The price covers the tests, the spoken diagnosis and the start of the repair once you accept it. A scorched socket takes less time than a damaged cable in the wall. A new socket, a certificate for minor works or a fuse board replacement changes the price.
From £75 an hour
Included when agreed
- Testing at the board and along the failed circuit until the cause is named
- A spoken diagnosis before any part is swapped
- Repair of the failed joint, accessory, cable or protective device once you accept the hourly work
- Making the circuit safe if it cannot be left live that day
- A minor works certificate when the repair needs one
Not included automatically
- A full house rewire or a new consumer unit as the first step
- Solar, battery, EV charger or forklift charger work
- Guesswork replacement of parts that have not failed
Ways to pay


- Pay by bank
- Bank transfer
- A socket, breaker or length of cable is added only when the tests show that part has failed.
- Where a Hager, Wylex, Contactum, BG Electrical or MK Electric part has failed, that part is added to the job.
- Fuse board replacement and emergency electrician attendance are each priced as a separate job.
How booking works
Tell us about the job
Tap Book Now and describe the work in the chat. Photos help.
Get your price
You see your price in the chat. A set price is paid at checkout; any other job is quoted first.
Choose your visit
Give your address and when you are free, and the visit is arranged.
Why choose Lighting Electrical
We work with Hager, Wylex, Contactum, BG Electrical, MK Electric, Varilight, myenergi, Ohme, Hypervolt, Andersen, Aico, FireAngel and Mira.
- Reviews
- 61
- Rating
- 4.7
- Trading since
- 2016
“Ten years on Colchester housing stock and I have seen most of it: terraces where the lighting circuit has been extended once too often, boards fitted before RCDs were standard, new builds with sockets nowhere near the kitchen. I check the earthing, the bonding and whether the supply will carry another load before I price anything, because the age of a house settles nothing on its own.”
Valandi Kotorri, Lighting Electrical
Book NowIs a warm plug safe to keep using?
A kettle plug can feel faintly warm straight after a boil. A plug that is painful to hold, that smells, or that leaves brown marks is a fault, so unplug it and stop using that socket. On the visit we test the socket and the plug and name the part that is heating.
Should I reset the breaker?
After the hot plug is out, raise a cool and silent breaker once. Leave it down if it opens straight away. Switching it up again and again heats the terminals.
Will the socket be changed on the visit?
The socket is changed on the visit only when the readings show it has failed. You hear the cause first, and fitting a new socket waits for your acceptance. A sound socket is left on the wall.
What paperwork do I get after the repair?
Changing a socket, a cable or a breaker brings a certificate for minor works. The certificate lists the test results for the job done and shows NAPIT registration. A full EICR, which inspects the whole installation, is arranged as separate work.
Could the appliance be at fault rather than the house wiring?
Yes. We try a sound plug in the hot socket and we try the suspect plug in a socket that has tested well. Heat that follows the appliance means the appliance or its plug. Heat that stays at the first socket means the socket or the cable.
Related problems
- Automatic gate not openingA gate that will not move has lost its supply, its safety beam or its motor control, so the outdoor circuit needs a test.
- Buzzing sound in the wallA buzz inside a wall is a loose joint, a dimmer or a damaged cable on that circuit.
- Circuit breaker keeps trippingThe breaker keeps tripping because a fault is still on the circuit, in an appliance, a cable, a joint or the protective device.
- Consumer unit tripping with nothing plugged inThe consumer unit trips with nothing plugged in because fixed wiring or the safety switch is sending current to earth.
- Downstairs circuit keeps trippingThe downstairs breaker or RCD opens because a socket, light, cable or appliance on that floor is leaking or overloaded.
- Driveway lights not workingDriveway lights go dark when the outdoor circuit, a sensor or a lantern fails, while rooms on another breaker stay lit.
Sources
- Electrical Safety First: Safety Guidance
- BS 7671: IET Wiring Regulations (18th Edition)
- HSE: Electrical Safety at Work
Updated 16 November 2026
