Security light won't turn off

A security light that stays on still has the sensor, the daylight control or the wall switch feeding the lamp. Lighting Electrical of Peterborough tests the lantern on the wall and names the part.

Calls answered 24/7

  • 10 years trading

Why does a security light stay on?

A security light stays on because the sensor keeps calling for light, the daylight control no longer switches it off, or the wall switch has latched an override. The lamp is a separate part from the control that feeds it.

  • Movement in front of the sensorA PIR is a passive infrared sensor. It looks for moving body heat and starts a timer that should turn the lamp off. A car, a shrub in the wind or a warm flue in that view starts the timer again, so the lamp never goes dark.
  • Daylight control no longer reading the skyA photocell measures daylight and should stop the lamp lighting while the sun is up. Paint, a leaf or a cobweb over that small window leaves the control in night mode. A failed photocell does the same and the lamp runs in full sun.
  • Override latched at the wall switchAn override keeps the lamp on without waiting for movement. It latches when the wall switch is turned off and back on in quick succession. The lamp then stays lit until that override is cleared at the wall switch.
  • Relay stuck inside the lanternA relay is the small switch inside the lantern that connects power to the lamp. A relay that sticks closed feeds the lamp with nobody in the yard. It also feeds the lamp in full sun.
  • Lamp wired to the permanent liveThe sensor needs a permanent live so it can watch while the lamp is off. The lamp should receive power only when the relay closes. Crossed wires put the lamp on the permanent live, so it glows for the whole time the lighting circuit is on.

What can I check safely on a security light?

The safe checks are the wall switch, a watch of the lamp in daylight, and a look at the sensor from the ground. Every screw stays in the lantern. The fuse board cover stays on.

  • Clear a latched overrideTurn the wall switch off and wait one full minute. Turn it on once and stand still. If the lamp then goes off after its timer, the override was latched. If the lamp stays on in bright sun, the photocell or the relay needs a test.
  • See what crosses the sensorLook from the ground at the sensor window. Note a road, a moving shrub, a boiler flue or people passing through that view. Constant crossings reset a healthy PIR. A still view with the lamp stuck on points to the control or the relay.
  • A check in bright sunDo this in bright sun after the one minute wait. A working photocell keeps the lamp off. A lamp that stays lit has a covered window, a failed photocell or a stuck relay.
  • The outside of the sensor windowWith the wall switch off, wipe cobwebs, leaves or dirt off the outside of the window only. Stop if the glass is cracked, wet inside or warm. Do not undo screws and do not pull the lantern off the wall.

When should I book for a security light that stays on?

Book Now when the lamp stays on in bright daylight after you have cleared the override, or when the lantern is hot, wet, buzzing or smelling of burning.

  • Still lit in full sunThe override is cleared and the yard is still. The lamp remains on in the middle of the day. The photocell, the relay or the wiring is feeding the lamp. That part needs a test with the circuit off.
  • On all night with nothing movingThe sensor looks over a quiet yard and the lamp never goes off. A healthy timer would have opened the relay. The sensor, the timer or the relay needs a test before the lamp runs every night.
  • Heat, water, a buzz or a burning smellA warm lantern, a buzz, brown marks or a smell of burning means a joint is failing. Rain inside the glass leaks current to earth. Earth is the safe path that carries a fault away from you. Switch the light off at the wall switch and Book Now.

What happens on a visit for a security light that stays on?

We test the lantern with its circuit switched off and name the part that is feeding the lamp before we change a sensor, a relay or a lantern. You hear that finding before any repair starts.

  • What the lamp has been doingWe ask whether the lamp stays on in daylight, all night, or only after the wall switch was flicked. We look at the sensor view from the ground. We note any wipe you have already done. The lantern stays closed until the circuit is off.
  • Tests with the lighting circuit offWe switch off the lighting breaker. A breaker is the switch on the fuse board for that circuit. We test the permanent live, the lamp wire, the photocell and the relay. Those readings separate a stuck relay, a dead photocell, a crossed wire and a break in the cable.
  • The part named before any further priceWe tell you the failed part before we fit anything. We check the earthing, which is the fault path back to the fuse board. We check the bonding, which joins metal pipework to that earth. We check that the supply can carry a replacement lantern. Only then do we write a price for anything beyond this repair.
  • Repair of the part that failedThe sensor, relay, joint or lantern is changed after you accept the repair. We run the lamp off and on in daylight, then with the sensor covered. Where the circuit was altered we record those tests on the certificate for the job, with our NAPIT registration on it. We leave the wall switch off when the circuit fails the test to go back on.

What does a security light fault cost?

Electrical Fault Finding & Repair is charged for the time on this lantern. The price covers the tests, the diagnosis we talk through with you, and the repair after you accept it. A latched override that needs no parts takes less time than a cable fault between the lantern and the fuse board. A new sensor, a certificate or a replacement lantern changes the price.

From £75 an hour

Included when agreed

  • Testing at the board and along the failed circuit until the cause is named
  • A spoken diagnosis before any part is swapped
  • Repair of the failed joint, accessory, cable or protective device once you accept the hourly work
  • Making the circuit safe if it cannot be left live that day
  • A minor works certificate when the repair needs one

Not included automatically

  • A full house rewire or a new consumer unit as the first step
  • Solar, battery, EV charger or forklift charger work
  • Guesswork replacement of parts that have not failed

Ways to pay

  • Visa
  • Mastercard
  • American Express
  • Apple Pay
  • Google Pay
  • Klarna
  • Pay by bank
  • Bank transfer
  • A lighting breaker from Hager, Wylex or Contactum, or a switch from MK Electric, BG Electrical or Varilight, is added only after the test names it.
  • Emergency electrician work is priced as its own job, separate from this fault finding visit.
  • A new fuse board is priced on its own when tests show the lighting breaker or the board has failed.

View the fault finding cost guide

How booking works

  1. Tell us about the job

    Tap Book Now and describe the work in the chat. Photos help.

  2. Get your price

    You see your price in the chat. A set price is paid at checkout; any other job is quoted first.

  3. Choose your visit

    Give your address and when you are free, and the visit is arranged.

Why choose Lighting Electrical

We work with Hager, Wylex, Contactum, BG Electrical, MK Electric, Varilight, myenergi, Ohme, Hypervolt, Andersen, Aico, FireAngel and Mira.

Photo of Valandi KotorriValandi KotorriElectrician
Reviews
61
Rating
4.7
Trading since
2016
“Ten years on Colchester housing stock and I have seen most of it: terraces where the lighting circuit has been extended once too often, boards fitted before RCDs were standard, new builds with sockets nowhere near the kitchen. I check the earthing, the bonding and whether the supply will carry another load before I price anything, because the age of a house settles nothing on its own.”

Valandi Kotorri, Lighting Electrical

Book Now

Questions about a security light that stays on

Still have a question?

Will you change the security light before finding the fault?

No. We test the sensor, the photocell, the relay and the cable before we name the failed part. The repair of that part starts after you accept it. A lantern that tests sound stays in place.

Should I switch the security light off while I wait?

Leave it on if the lantern is cool, dry and quiet and you have only found a latched override. Switch it off at the wall switch if it is hot, buzzing, wet inside or smelling of burning. Leave that switch off until we test the circuit.

What paperwork do I get after the repair?

Where we change the sensor, the lantern or the cable, the certificate for that job lists the tests and shows our NAPIT registration. If the override was latched and we change nothing, we tell you so and we write nothing for an unaltered circuit. An Electrical Installation Condition Report inspects the whole installation and is booked as its own job.

Will a new fuse board stop the lamp staying on?

Only if the tests show the lighting breaker or the board is sending power to the lamp all the time. A stuck relay or a failed photocell keeps the lamp on after a board change. We price fuse board replacement on its own after those tests.

Do you repair the light on the same visit?

Yes, once you accept the repair of the part the tests have named. We change a sensor, a relay, a joint or the lantern on that visit. A fuse board change waits for its own price.

Related problems

Sources

Updated 16 November 2026

Book or ask a question

Calls answered 24/7

Areas we cover (2)