PIR light not coming on

A dark PIR light means the sensor, the lamp or the lighting circuit has failed, and Lighting Electrical tests that fitting in Peterborough.

Calls answered 24/7

  • 10 years trading

Why is my PIR light not coming on?

A PIR light stays off when the sensor thinks it is daytime, the lamp has failed, or the lighting circuit has lost power. PIR means passive infrared, a sensor that looks for body heat.

  • The daylight setting is holding it offThe daylight control is marked lux on many lanterns. Lux sets how dark the sky must be before the lamp is allowed to switch. Set for night, the lantern stays dark in the day while people walk past. The sensor is doing what it was set to do.
  • The lamp or the LED has failedA click from the sensor with a dark lamp means the bulb, the LED chips or the driver has failed. The driver is the small unit that powers the LED. The lighting circuit is still live at the fitting.
  • Dirt or a cobweb over the sensorThe sensor window sits on the lantern face. Paint, dust or a cobweb blocks the view of body heat, so the lamp never switches on. A photocell under the same dirt reads the sky as bright and holds the lamp off.
  • The lighting circuit has openedA breaker is the switch in the fuse board that guards one circuit. If that breaker has opened, every light on it goes dark, including the sensor lantern. An RCD, the switch that opens when current leaks to earth, does the same when it covers that circuit.
  • The sensor module has failedThe PIR module is the part that decides when to switch. Water behind an outdoor lantern, or a burnt joint at the lamp, leaves the module dead. The rest of the lighting circuit stays on.

What can I check on a sensor light safely?

You can use the wall switch, read the fuse board through its cover, and wipe the outside of the sensor. Leave the lantern screws in and keep off the cables.

  • The wall switch that feeds the lanternMany sensor lights still have a normal switch indoors. Leave that switch on for automatic operation. If nothing happens, turn it off, wait a few seconds, and turn it on again. Do not take the switch apart.
  • The lighting breaker with the cover shutLook through the fuse board cover. A lighting breaker sitting down means that circuit is off. One reset is reasonable if the board is cool, quiet and has no burning smell. If it opens again, leave it down.
  • The sensor window on the outsideWipe the plastic sensor window with a dry cloth. Clear cobwebs and leaves. Do not open the lantern or touch the terminals. A clean window lets the sensor see movement again.
  • Whether other lights on that circuit workTurn on a light that shares the same breaker. Dark lamps on that breaker mean the fault is the circuit, not only the sensor. Lamps that work mean the fault sits at this lantern.
  • A walk past after darkWait until it is properly dark, then walk across the front of the lantern. A lamp that stays off in daylight and lights after dark is following its lux setting. A lamp that stays off at night as well needs a test.

When should I book for a sensor light not working?

Book Now when the lantern stays dark after the switch is on, one breaker reset has failed, and the sensor window is clean. A lantern that only lights in full dark can wait.

  • It stays off after darkThe switch is on, other lights on that breaker work, and a walk past at night does nothing. The sensor, the lamp or the joint in the lantern has failed. Book Now for a test of that fitting.
  • The light trips the breakerThe lighting breaker or RCD opens when the sensor tries to switch. Current is leaking to earth, or the lantern cable is shorted. Leave the breaker off. Another reset heats the joint.
  • Water, heat or a burning smellAn outdoor lantern with water inside, a warm fitting or a burning smell needs that circuit left off. Use the breaker handle only. Keep your hands off the lantern screws and the fuse board cover.
  • It flashes or clicks and stays dimA click with no light, a brief flash, or a lamp that stays very dim points to a failing sensor module or LED driver. The fitting needs a test before the part is changed.

What happens on a visit for a dead sensor light?

We test the lantern and the lighting circuit and name the failed part before anything is changed. The repair starts after you accept it.

  • Which lantern failed and whenWe ask which sensor light is dark, whether it fails by day and by night, and whether the breaker has opened. We look at the fuse board with the cover on and at the lantern on the wall. A wall lantern with a PIR sensor is a fitting we fit and repair.
  • Tests with the circuit switched offWe switch off the lighting circuit at the breaker. A dead test checks the cable and the lantern while they are safe to handle. The readings separate a failed sensor, a failed lamp, a leak to earth and a break in the cable.
  • The failed part named before a changeYou hear the failed part before a sensor, a lamp or a lantern is changed. Earthing, the path that carries fault current, is checked on the visit. Bonding, the link from metal pipes to earth, and spare capacity on the supply are checked before any further price.
  • Repair and the minor works certificateOnce you accept the repair we fit the failed part and test the circuit again. Where the circuit is altered we issue a minor works certificate under our NAPIT registration. If the lantern cannot be left live, that breaker stays off and the other circuits stay on.

What does a sensor light fault visit cost?

Fault finding and repair is charged by the hour. That time covers tests on the sensor light and its circuit, the diagnosis we give you, and the start of the repair once you accept it. A lantern that only needs a new lamp takes less time than a cable fault back to the fuse board. A new part, a minor works certificate, or Lighting Installation as its own job changes the price.

From £75 an hour

Included when agreed

  • Testing at the board and along the failed circuit until the cause is named
  • A spoken diagnosis before any part is swapped
  • Repair of the failed joint, accessory, cable or protective device once you accept the hourly work
  • Making the circuit safe if it cannot be left live that day
  • A minor works certificate when the repair needs one

Not included automatically

  • A full house rewire or a new consumer unit as the first step
  • Solar, battery, EV charger or forklift charger work
  • Guesswork replacement of parts that have not failed

Ways to pay

  • Visa
  • Mastercard
  • American Express
  • Apple Pay
  • Google Pay
  • Klarna
  • Pay by bank
  • Bank transfer
  • The hourly work pays for the tests, the spoken diagnosis and the repair of the part that failed, after you accept it.
  • A sensor, a lamp or a length of cable is added only when the tests show that part has failed.
  • Attendance under the emergency electrician service carries its own price, apart from the hourly fault finding.

View the fault finding cost guide

How booking works

  1. Tell us about the job

    Tap Book Now and describe the work in the chat. Photos help.

  2. Get your price

    You see your price in the chat. A set price is paid at checkout; any other job is quoted first.

  3. Choose your visit

    Give your address and when you are free, and the visit is arranged.

Why choose Lighting Electrical

We work with Hager, Wylex, Contactum, BG Electrical, MK Electric, Varilight, myenergi, Ohme, Hypervolt, Andersen, Aico, FireAngel and Mira.

Photo of Valandi KotorriValandi KotorriElectrician
Reviews
61
Rating
4.7
Trading since
2016
“Ten years on Colchester housing stock and I have seen most of it: terraces where the lighting circuit has been extended once too often, boards fitted before RCDs were standard, new builds with sockets nowhere near the kitchen. I check the earthing, the bonding and whether the supply will carry another load before I price anything, because the age of a house settles nothing on its own.”

Valandi Kotorri, Lighting Electrical

Book Now

Questions about a PIR light not coming on

Still have a question?

Will you change the sensor light before you find the fault?

No. Testing comes first. We name the dead sensor, lamp, joint or cable, and the repair waits until you accept it. A lantern that tests sound stays where it is.

Do I get paperwork after a sensor light repair?

Where the repair alters the lighting circuit, the minor works certificate lists those tests and our NAPIT registration. If we only isolate the lantern and change nothing, you still get the readings and the named part. An Electrical Installation Condition Report, called an EICR, is a separate full inspection of the installation.

Can the rest of the lights stay on?

Yes. We switch off only the circuit that feeds the dead lantern. Every other circuit stays on, and that breaker goes back on after the repair unless the lantern cannot be left live.

Is a new fuse board the fix for a dead sensor light?

The lantern needs a new fuse board where the lighting breaker or the board itself has failed the tests. A dead sensor still leaves the lantern dark on a sound board. Fuse board replacement then has its own written price.

What if the lantern lights for a second and goes out?

A short flash means the sensor switches and the lamp or its driver fails to stay lit. We measure the lantern with the circuit switched off and name that part. The lamp or sensor is replaced on the visit once you accept the repair.

Related problems

Sources

Updated 16 November 2026

Book or ask a question

Calls answered 24/7

Areas we cover (2)