Plug socket feels hot
A plug socket feels hot when a loose joint or an overloaded outlet heats the contacts. Lighting Electrical in Peterborough isolates that circuit. We test the socket.
Calls answered 24/7
- 10 years trading
Why does a plug socket feel hot?
A plug socket feels hot because a poor joint or too much load turns current into heat at the contacts. The warmth is in the face, the plug pins or the cable terminal behind the plate.
- A loose terminal behind the socketA screw that has slackened raises resistance where the cable meets the socket. Current through that resistance heats the terminal. The face then warms and the plastic can brown around the pin holes.
- Socket contacts that no longer gripWorn contacts arc against the plug pins while an appliance runs. Arcing is a spark jumping across a poor fit. The pins and the plate heat, even when the appliance itself is sound.
- Too much load in one outletA kettle, a heater or a tumble dryer on a multiway block draws more current than one socket is built to carry. The block and the socket terminals both warm. The two outlets on a double socket use the same terminals.
- A damaged plug in a sound socketBent pins or a cracked plug body sit badly in the contacts. Heat starts on the pins and spreads into the face. The same plug can heat the next outlet it is put into.
- A poor joint on the socket circuitA ring final circuit leaves the fuse board, passes through the sockets and comes back. A radial circuit runs from the board and ends at the last socket. A loose joint on either layout heats the nearest face.
What can you check safely on a hot socket?
You can unplug, look at the face and switch the socket off. You can also read the fuse board through its closed cover. Covers stay on and cables stay untouched.
- Whether the plug or the face is hotterPull the plug straight out and set it aside. Hotter pins, with a cooler plate, point to the plug or the appliance lead. A hotter plate points to the socket joint. Leave the plug and the appliance closed.
- Brown marks, a smell or soft plasticLook at the pin holes and the edge of the plate. Brown stains, a burning smell or plastic that has softened mean the joint has been overheating. Leave that socket unused.
- The socket switch and the fuse boardSwitch the socket off at its own switch if it has one. If the plate is still hot, or you smell burning, open the socket breaker. A breaker is the switch on the fuse board that protects one circuit. Use only that handle. The cover stays shut.
- What was plugged in and which faces are warmNote the appliance that was in the socket. Touch a nearby socket face and one in another room with the back of your hand. One hot face points to that outlet. Several hot faces point to the circuit.
When should you book for a hot socket?
Book Now when the socket face is hot, when it smells of burning, or when it stays warm after the plug is out. A mildly warm plug top on a kettle, with a cool socket face, is a separate case.
- The face is hot after you unplugHeat that remains in the plate after the appliance is out comes from the terminal or the contacts. Leave the socket switch off. Book Now so the circuit can be tested before anyone uses it again.
- A burning smell, a buzz or scorch marksA smell of hot plastic, a buzz from the plate or brown marks at the pin holes mean the joint is arcing. Switch that circuit off at the breaker handle. Keep the fuse board cover on.
- The fuse board is warm or the breaker opensA warm fuse board means the fault may sit beyond one plate. A socket breaker that opens after the face was hot means the same. Leave that breaker off. Other circuits can stay on when their breakers are up and the board is cool.
What happens on a visit for a hot socket?
We switch off the hot socket circuit, test it dead and name the failed part before anything is changed. Other circuits stay on where the fuse board allows that.
- Which socket heated and what was plugged inWe ask which plate got hot, what was plugged in and whether the heat stayed after the plug came out. We stand at the fuse board with you and open the socket breaker. Screws stay in until a tester shows that circuit is dead.
- Tests on the dead socket and its cableWith the circuit off we measure whether the conductors still join. We then measure whether current could leak between them. The readings separate a burnt terminal, a broken ring and a tired socket. The plate comes off only when the readings or the heat marks point to it.
- The failed part is named before a repairWe tell you whether the socket, the cable joint or the breaker failed. We check the earth path, which carries fault current so a breaker can open. We check bonding, which ties metal service pipes to that earth path. We check the supply can feed the load before we write any further price.
- Repair, a retest and the certificateThe repair of the failed socket or joint starts once you accept it. We test the circuit again after the work. Where the circuit is altered we complete a minor works certificate for Lighting Electrical, and our NAPIT registration is on it. If the circuit is not safe to energise, we leave its breaker off.
What does a hot socket visit cost?
The price covers the visit, the tests on the hot socket circuit and making that circuit safe to leave. Time rises if we have to open several sockets on a ring to find the hot joint. A replacement socket, a minor works certificate or a later fuse board replacement changes the price. Emergency electrician attendance and a booked repair under Electrical Fault Finding & Repair are charged as separate jobs.
From £90 an hour
Included in the call-out
- Attendance at the property in Peterborough or a nearby Essex town
- Isolation of the failed circuit, fitting or board
- Fault finding on the circuit that has gone down
- Temporary making safe so the rest of the installation can be used where that is possible
- A written note of what failed and what work should follow
Not included automatically
- A full house rewire or a planned consumer unit replacement on the same visit unless already quoted
- Parts we do not carry in the van, which we price in writing before we fit them
- Work on another trade such as gas, plumbing or structural fabric
Ways to pay


- Pay by bank
- Bank transfer
- We add a socket from MK Electric, BG Electrical, Hager, Wylex or Contactum only after the tests show that outlet has failed.
- We price fuse board replacement on its own when the breaker or the board has failed.
- We include a minor works certificate in the price only for the circuit we alter on this visit.
How booking works
Tell us about the job
Tap Book Now and describe the work in the chat. Photos help.
Get your price
You see your price in the chat. A set price is paid at checkout; any other job is quoted first.
Choose your visit
Give your address and when you are free, and the visit is arranged.
Why choose Lighting Electrical
We work with Hager, Wylex, Contactum, BG Electrical, MK Electric, Varilight, myenergi, Ohme, Hypervolt, Andersen, Aico, FireAngel and Mira.
- Reviews
- 61
- Rating
- 4.7
- Trading since
- 2016
“Ten years on Colchester housing stock and I have seen most of it: terraces where the lighting circuit has been extended once too often, boards fitted before RCDs were standard, new builds with sockets nowhere near the kitchen. I check the earthing, the bonding and whether the supply will carry another load before I price anything, because the age of a house settles nothing on its own.”
Valandi Kotorri, Lighting Electrical
Book NowIs a slightly warm plug the same as a hot socket?
No. A kettle plug can feel warm at the pins while the socket face stays cool, and that plug should come out. A face that is hot to the touch is a fault in the socket or the joint. Leave that circuit switched off.
Can I use the other side of a double socket?
No. Both sides of a double socket use one set of terminals. Heat on one side is heat in that joint. We test the whole plate with the circuit off.
Will the socket be replaced on the same visit?
We name the failed socket, joint or breaker before any part is changed. The repair starts on the visit once you accept it. A socket that tests sound stays on the wall.
Why did the breaker stay up if the socket was hot?
A loose terminal can get hot without pulling enough extra current to open the breaker. The breaker reacts to overload and to current leaking to earth. It does not open for every warm joint, so the circuit still has to be switched off by hand.
What paperwork follows a hot socket repair?
Where we change the socket or the cable, a minor works certificate records the tests for that job and shows our NAPIT registration. If we only isolate the circuit and change nothing, you get the readings and the name of the failed part. An EICR, short for Electrical Installation Condition Report, is a separate inspection of the whole installation.
Related problems
- Brown marks on a socket or plugBrown marks on a socket or plug mean the connection has overheated, so that circuit stays off until it is tested.
- Burning plastic smell from electricsA burning plastic smell means the insulation on a live joint is getting hot, so that circuit stays switched off until it is tested.
- Burning smell from a socketA burning smell from a socket means a connection is overheating and that circuit should stay off until it is tested.
- Burning smell from the fuse boxA burning smell at the fuse box means a connection or device is overheating, so that circuit stays off until it is tested.
- Electric shock from a light switchA shock from a light switch means the switch face is carrying current and that lighting circuit should be isolated.
- Electric shock from the showerA shock from the shower means current is on the water, the case or the taps, so that circuit stays off until it is tested.
Sources
- Electrical Safety First: Safety Guidance
- BS 7671: IET Wiring Regulations (18th Edition)
- HSE: Electrical Safety at Work
Updated 16 November 2026
