USB socket stopped charging
A USB socket stops charging when the small charger inside the plate fails, while the plug outlets beside it stay live. Lighting Electrical in Peterborough tests that plate and fits a replacement socket when the charger has failed.
Calls answered 24/7
- 10 years trading
Why does a USB socket stop charging?
A USB socket stops charging because the charger in the plate has failed, the cable or device will not draw, or the circuit feeding the plate has lost power. Plug outlets on that plate stay live when only the charger has failed.
- The charger inside the plate has failedThe charger inside the plate turns mains voltage into the low voltage the USB ports supply. Heat in the back box, the box sunk in the wall behind the plate, wears that charger out. The plug outlets keep working because they do not use that charger.
- Both ports share one outputSome plates feed both USB ports from one output. A phone and a tablet together then ask for more than that output supplies. Charging slows or stops while the plug outlets stay live and the plate is sound.
- The cable or the device will not drawA damaged cable draws nothing from a sound USB port. A device that needs a stronger charger does the same. When that device charges from a separate plug in charger, the plate is not the failed part.
- The circuit feeding the plate has openedThe USB ports and the plug outlets die together when the circuit loses power. A breaker is the switch on the fuse board that guards one circuit. An RCD is a safety switch that opens when current leaks to earth.
- A loose terminal is overheatingA loose terminal where the cable meets the plate heats up in use. That heat kills the charger before the plug outlets fail. Brown marks at the outlets show the joint is burning.
What can you check safely on a USB socket?
You can try a cable and device that already charge somewhere else, and you can see whether the plug outlets on the same plate still work. Leave the socket screws in and leave the fuse board cover on.
- A cable and device that charge elsewhereUse a cable that already charges this device from another charger. If that pair works elsewhere and fails in both ports here, the plate needs a test. If the pair fails everywhere, the cable or the device is the failed part.
- The plug outlets on the same platePlug a lamp you know works into the outlets on the USB plate. A lit lamp means those outlets are live and the charger in the plate is the part to test. A dead lamp means the circuit feeding the plate needs the test.
- One device at a timeUnplug every lead from the USB ports. Charge one device from one port. Then try the other port with the same device.
- Heat, noise or brown marksA warm plate, a buzz or brown marks around the outlets mean a joint is overheating. Stop using that plate. Leave every screw in place.
When should you book for a USB socket?
Book Now when a device and cable that charge elsewhere still draw nothing here, or when the plate is hot, cracked or smelling of burning. A dead lamp in the plug outlets on that plate needs a booking too.
- A known cable still will not chargeThe device and cable already charge from another charger. They still draw nothing from both ports on this plate. The plug outlets on the plate still work.
- The plate is hot or smells of burningHeat, a buzz or a burning smell means a terminal is arcing. Arcing is a spark jumping a loose joint. Leave that socket unused and Book Now.
- The plug outlets are dead as wellUSB ports and plug outlets dead together mean the circuit has opened. The charger in the plate is not the only part to test. Leave the breaker off when it will not stay on.
What happens on a USB socket visit?
We test the USB plate and its circuit, then we fit a new plate only when the charger inside it has failed. We name the failed part before any plate comes off.
- What still charges and what is deadWe ask which USB port has stopped, which cable and device you tried, and whether a lamp still runs from the plug outlets on that plate. We look at the fuse board with the cover on and note any switch that has opened.
- Tests with the circuit switched offWe switch off the circuit that feeds the plate. With the circuit off we test the cable for a break, a short and a leak to earth. The readings separate a failed charger, a dead plug outlet and a fault further along the cable.
- Earthing and load before a new plateWe tell you the failed part before a plate is changed. Earthing is the path that lets fault current open a breaker, and we check it on the visit. Bonding is the link from metal pipes to that earth, and we check that link too. We also check that the circuit can carry the load before we price the new plate.
- The new plate and the certificateThe new plate goes on after you accept it. We test the circuit again and leave a minor works certificate for that change, with our NAPIT registration on it. A plate that tests sound stays in place.
What does a failed USB socket cost?
The price covers testing one USB socket and fitting a new plate when the charger inside that plate has failed. A second plate on the same visit changes the price. Plaster after the plate comes off changes it too. Tracing the circuit when the plug outlets are dead as well is priced as Electrical Fault Finding & Repair.
From £85
Included when agreed
- Fitting a new socket or replacing an existing socket at the quoted position
- Changing a light switch or damaged faceplate when that line is on the quotation
- Checking earthing, bonding and whether the circuit can carry the extra load
- The relevant electrical paperwork when the work is complete
- Removing packaging and leaving the room ready to use the new point
Not included automatically
- Plastering, painting or making good after any chasing
- A house rewire when the circuit cannot take another point
- A consumer unit replacement unless that is quoted as its own job
Ways to pay


- Pay by bank
- Bank transfer
- We fit a plate from MK Electric, BG Electrical or Varilight only after the test shows the charger has failed.
- Plaster and paint after the plate comes off are written as their own line.
- Electrical Fault Finding & Repair is the job when the plug outlets are dead as well as the USB ports.
How booking works
Tell us about the job
Tap Book Now and describe the work in the chat. Photos help.
Get your price
You see your price in the chat. A set price is paid at checkout; any other job is quoted first.
Choose your visit
Give your address and when you are free, and the visit is arranged.
Why choose Lighting Electrical
We work with Hager, Wylex, Contactum, BG Electrical, MK Electric, Varilight, myenergi, Ohme, Hypervolt, Andersen, Aico, FireAngel and Mira.
- Reviews
- 61
- Rating
- 4.7
- Trading since
- 2016
“Ten years on Colchester housing stock and I have seen most of it: terraces where the lighting circuit has been extended once too often, boards fitted before RCDs were standard, new builds with sockets nowhere near the kitchen. I check the earthing, the bonding and whether the supply will carry another load before I price anything, because the age of a house settles nothing on its own.”
Valandi Kotorri, Lighting Electrical
Book NowWhy do the plugs work when the USB ports do not?
The charger for the USB ports sits inside the plate and is separate from the plug outlets. Those outlets stay live when only the charger has failed. We confirm that split on a test before we change the plate.
Will you fit a new USB socket on the visit?
We fit a new plate on the visit when the test shows the charger has failed and you accept the new plate. A sound plate stays where it is. A circuit that is dead at the plug outlets is traced as Electrical Fault Finding & Repair.
Will my other circuits stay on?
We switch off only the circuit that feeds the USB socket. Other circuits stay on while that circuit is tested. We switch it back on after the test unless it is unsafe to leave live.
What certificate do I get after the socket is changed?
A minor works certificate records the tests when we change the plate on the existing circuit. Our NAPIT registration is printed on that certificate. An EICR is a separate inspection of the whole installation.
Why does charging stay slow on a USB socket?
Some plates feed both USB ports from one output. A phone and a tablet together then ask for more than that output supplies, so charging slows on a sound plate. We change the plate only when the test shows the charger has failed.
Related problems
- Cracked plug socketA cracked plug socket stays unused until the face is replaced and the terminals behind it are tested.
- Extension lead getting hotA hot extension lead is overloaded, so the appliance needs a fixed socket instead of that lead.
- Loose or wobbly plug socketA loose plug socket has a moving faceplate or worn contacts, and we replace it after the circuit is tested.
- One side of a double socket not workingOne outlet on a double socket goes dead when its contacts or switch fail and the other outlet still has power.
- Sparks when turning on a socketA spark as the socket switch closes means a worn socket contact or a damaged plug.
- Yellowed or discoloured socket face plateEven yellowing across a cool face plate is aged plastic. Brown marks around the pin holes mean the socket is heating and should be replaced.
Sources
- Electrical Safety First: Safety Guidance
- NICEIC: Householder Guidance
- BS 7671: IET Wiring Regulations (18th Edition)
Updated 16 November 2026
