Is old cloth or rubber wiring dangerous?

Old cloth or rubber wiring is dangerous once the insulation cracks and leaves bare copper. Lighting Electrical tests those circuits in Peterborough and replaces the failed runs with new cable.

Calls answered 24/7

  • 10 years trading

Why does old cloth or rubber wiring fail?

Cloth and rubber insulation dries, cracks and falls away from the copper, so the conductors can touch and overheat. The braid and the rubber were a sound covering when the cable went in. Heat in the loft and years of load destroy that covering.

  • Rubber insulation that has perishedMany older lighting and socket cables use vulcanised rubber under a cloth braid, from the years before PVC, the plastic sheath on modern cable. Heat from lamps and a warm loft dries that rubber until it splits. Bare copper then lies in the ceiling. The conductors touch and the fuse or the breaker opens.
  • Cloth braid that no longer coversThe cloth braid is only an outer wrap. It stops protecting the copper once the rubber inside has crumbled. Dust then sits on the bare strands. Current that leaves the copper for timber or metal is a leak to earth, the path a fault should take back to the fuse board, and that leak warms the wood.
  • Lights with no earth wireMany lighting cables of that age have a live and a neutral only. There is no earth wire to clear a fault. A metal switch or a metal lamp can become live when rubber falls against the case. Old rewireable fuses do not open on a small leak. An RCD, the device that switches off when current leaves a circuit, is often missing from that fuse board.
  • Cable that powders when movedPerished rubber can look whole until a loft board shifts it or insulation is pushed against it. The sheath then powders off the copper. Lights on that circuit start to trip. A ceiling rose on the same run can show a brown scorch.
  • Modern load on thin old copperOld rubber cable is thin beside the current a kettle, a heater or extra sockets draw today. The copper runs hot. Heat splits the remaining rubber faster. A new socket or a charger must not be added to that cable.

What can I look at without touching the cable?

You can look at cable already in the open, read the closed fuse board, and note which lights flicker. You do not take a plate off. You do not handle a conductor.

  • Cable already open in the loftStand on the boards and look, without lifting a cable. Cloth braid, black rubber, cracks, dull green copper or crumbs of rubber on a joist are the old wiring. Leave every strand where it lies.
  • Marks on a rose or a switchA brown ring on a ceiling rose or a switch plate, or a sharp smell of hot rubber, shows heat at that fitting. Leave the screws in place. Turn that light off at the wall switch only.
  • The fuse board cover left shutLook through the cover. Rewireable fuse carriers, cloth tails and a wooden or metal case sit with this old cable. If a carrier is blackened or the case is warm, leave it alone. Do not pull a fuse carrier out.
  • Lights that flicker togetherNote the rooms where lamps flicker, dim or blow a fuse as a group. That pattern marks the circuit still on cloth or rubber. One spent lamp in a cool fitting is a different fault.

When should I book for cloth or rubber wiring?

Book Now when bare copper is already in sight, a ceiling rose is scorched, or the light fuse will not stay up. Cable left in use in that state keeps bare conductors in the ceiling.

  • Bare copper or cracked rubberCracks, missing rubber or bright copper are visible in the loft or beside a fitting. That circuit can short or leak to earth. Switch those lights off at the wall switch.
  • A burning smell or a scorched roseHot rubber has a sharp smell. Brown marks on a ceiling rose mean the cable or the joint there is heating. Leave that light off. Do not open the rose.
  • A light fuse that opens againThe lighting fuse or the lighting breaker opens when those lamps are on, and it opens again after one reset. The fault sits in the old cable or in a fitting on it. Leave that fuse out or that breaker down.
  • Work that would bury the cableLoft insulation, a new kitchen, extra sockets or an EV charger must not go onto perished rubber. We test the insulation before that work. House Rewiring replaces each circuit that fails the test.

What happens on a visit for old cloth wiring?

We look at the visible cloth or rubber, test those circuits with the power off, and name the failed runs before any cable is replaced. House Rewiring is then quoted for the circuits that no longer insulate.

  • The visible cable and the fuse boardWe ask which lights trip, flicker or smell hot. We look at cloth or rubber already visible in the loft and at fittings. We open the fuse board only after a tester shows that the circuit is dead.
  • Insulation tests on the old circuitsWith the circuit off, an insulation test shows whether current leaks between the conductors or to earth. A low reading means the rubber has failed even where the braid still looks whole. We test each old lighting run and each old socket run apart from cable that is already plastic.
  • Earthing, bonding and spare capacityBefore any price for new cable, we measure the earthing, confirm the bonding to the metal pipes, and see whether the supply can feed the extra load. Earthing is the fault path that lets a fuse open. Bonding joins those pipes to that earth. The age of the house, on its own, does not set the price.
  • New cable, tests and the certificateOnce you accept the quote, we remove the failed cloth or rubber and run the new cable, sockets and switches named on it. A consumer unit is fitted where the old fuses come out. We test the new circuits, leave an Electrical Installation Certificate, and notify through NAPIT where Building Regulations require notice. Cable that passes the insulation test stays.

What does work on cloth wiring cost?

Electrical Fault Finding & Repair covers the inspection and the insulation tests, and we tell you which cloth or rubber runs have failed. House Rewiring covers removal of those runs, new cable, sockets and switches, a consumer unit if the old fuses come out, later tests, and the Electrical Installation Certificate. More failed circuits, plaster chases, or loft work change the price. The written quote names the rooms first.

From £2,400

Included when agreed

  • Removal of the old lighting and socket circuits named on the quote
  • New cables, sockets, switches and a replacement consumer unit, also called a fuse board
  • Testing of every new circuit and an Electrical Installation Certificate at the end
  • NAPIT notification where Building Regulations require it
  • Making good of chases we cut, ready for a decorator

Not included automatically

  • Plastering, painting, flooring and kitchen fitting after the cables are in
  • Appliance supply, such as a cooker or electric shower, unless those items are listed on the quote
  • Rewiring of outbuildings, garages or commercial units that sit outside the named rooms

Ways to pay

  • Visa
  • Mastercard
  • American Express
  • Apple Pay
  • Google Pay
  • Klarna
  • Pay by bank
  • Bank transfer
  • One failed lighting circuit is a smaller job than lights and sockets that are both still on cloth or rubber.
  • A new Hager, Wylex, Contactum, BG Electrical or MK Electric consumer unit is on the quote only when the old fuses come out.
  • An EICR, short for Electrical Installation Condition Report, is a separate inspection of the whole installation and carries its own price.

View the house rewiring cost guide

How booking works

  1. Tell us about the job

    Tap Book Now and describe the work in the chat. Photos help.

  2. Get your price

    You see your price in the chat. A set price is paid at checkout; any other job is quoted first.

  3. Choose your visit

    Give your address and when you are free, and the visit is arranged.

Why choose Lighting Electrical

We work with Hager, Wylex, Contactum, BG Electrical, MK Electric, Varilight, myenergi, Ohme, Hypervolt, Andersen, Aico, FireAngel and Mira.

Photo of Valandi KotorriValandi KotorriElectrician
Reviews
61
Rating
4.7
Trading since
2016
“Ten years on Colchester housing stock and I have seen most of it: terraces where the lighting circuit has been extended once too often, boards fitted before RCDs were standard, new builds with sockets nowhere near the kitchen. I check the earthing, the bonding and whether the supply will carry another load before I price anything, because the age of a house settles nothing on its own.”

Valandi Kotorri, Lighting Electrical

Book Now

Questions about old cloth or rubber wiring

Still have a question?

Is cloth wiring dangerous if the lights still work?

Yes. The lamps can still light while the rubber is cracked and the copper is bare in the loft. A short or a leak starts when the strands move or when dust bridges them. We test the insulation with the circuit off and tell you which runs have failed.

Do you rewire every room?

No. We replace each circuit that fails the insulation test and we leave cable that still insulates. The House Rewiring quote lists the rooms and the circuits before any old cable comes out. A whole house is quoted only when failed cloth or rubber runs through the rooms in use.

Can I lay loft insulation over the old cable?

No. Insulation packed over perished rubber traps heat and hides bare copper. Leave the cable uncovered, and do not staple it or pull it. We test it first. House Rewiring then puts new cable in where the rubber has failed.

Will a new fuse board make the cloth cable safe?

No. New devices in the consumer unit do not put insulation back on bare copper. The old cable can still short in the ceiling. Fuse board replacement is a separate quote when the fuses change and the cable stays. On a rewire, the new consumer unit is listed with the new cable.

What certificate do I get after the cable is replaced?

When we renew circuits you get an Electrical Installation Certificate for that work. We notify through NAPIT where Building Regulations require notice. An EICR is a separate inspection of the whole installation, and we issue it only when that is the job you booked.

Related problems

  • Aluminium wiring in the houseAluminium cable overheats at loose joints. We test it, write the electrical installation condition report, and price any copper replacement separately.
  • Automatic gate not openingA gate that will not move has lost its supply, its safety beam or its motor control, so the outdoor circuit needs a test.
  • Bathroom fan stopped workingA stopped extractor fan means a seized motor, an open switch, or a fault on the circuit that feeds it.
  • Brown marks on a socket or plugBrown marks on a socket or plug mean the connection has overheated, so that circuit stays off until it is tested.
  • Burning plastic smell from electricsA burning plastic smell means the insulation on a live joint is getting hot, so that circuit stays switched off until it is tested.
  • Burning smell from a socketA burning smell from a socket means a connection is overheating and that circuit should stay off until it is tested.

Sources

Updated 16 November 2026

Book or ask a question

Calls answered 24/7